All-grain Homebrew Beer Recipes | Page 7 | Browse 225,000+ at Brewer's Friend

Author:

Professor Zymie

Boil Size: 7.5 Gallons

Boil Time: 90

Boil Gravity: 1.044

Efficiency: 72

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.5

Primary Temp: 68 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 3/31/2016 8:05 PM

Notes: 6 qts. @ boiling to increase to 170

Author:

Boil Size: 24 Litres

Boil Time: 90

Boil Gravity: 1.071

Efficiency: 70

Mash Thickness: 2.43

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.0

Primary Temp: 21 ° C

Priming Method: Inverted sugar

Priming Amount: 10g/L

Creation Date: 2/8/2015 9:23 AM

Notes: Recipe found on the internet, I made smaller modifications.

Cane sugar and invert sugar added after peak fermentation to primary. I used Lyle's Golden Syrup insted of invert sugar.

Author:

RockyMtnGT

Boil Size: 7.75 Gallons

Boil Time: 60

Boil Gravity: 1.051

Efficiency: 70

Mash Thickness: 1.25

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 68 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 8/12/2016 11:05 PM

Notes: Adjust salts as needed. Recipe is built based on RO/Distilled water

This is NOT a NEIPA, but has wonderful tropical fruit flavors and aromas. While the IBU number is high, the perceived bitterness is low. My wife enjoys it and she hates IPA's

Author:

Bigbeavk

Boil Size: 8 Gallons

Boil Time: 90

Boil Gravity: 1.041

Efficiency: 80

Mash Thickness: 1.25

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 52 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 9/27/2014 6:13 PM

Notes: Ferments for about 3 weeks @50°F then do a Diacytl rest for 3 or 4 days @63°F. No additional yeast required for bottling as it will carb up with 4.5oz corn sugar in about 10 days. Store in fridge to lager for a month or so if you can keep out of it. Or keg it and allow the same time for lagering. I've made this 6 times and there is not much difference between using german pils or american pils. This is a very good Pilsner that I constantly brew!
I upped the Perle by a half once and scaled up to 6 gal from the original recipe found on HBT.

Author:

Craftbeerchannel

Boil Size: 26 Litres

Boil Time: 60

Boil Gravity: 1.047

Efficiency: 58

Mash Thickness: 3.14

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 7/28/2020 9:43 AM

Notes:

Author:

bisandcan

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.071

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 6/26/2015 11:56 PM

Notes:

Author:

bradoslovich

Boil Size: 12 Gallons

Boil Time: 90

Boil Gravity: 1.071

Efficiency: 75

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 2/1/2013 12:20 AM

Notes: http://www.homebrewtalk.com/f12/firestone-walker-wookey-jack-clone-attempt-333436/

Author:

Newk

Boil Size: 7 Gallons

Boil Time: 60

Boil Gravity: 1.039

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 67 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/1/2017 1:38 PM

Notes:

Author:

LaOnda70

Boil Size: 7 Litres

Boil Time: 70

Boil Gravity: 1.215

Efficiency: 56

Mash Thickness: 3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 22 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 9/9/2014 8:56 AM

Notes: OG 1062 FG1010

Author:

jcmurray75

Boil Size: 6.5 Gallons

Boil Time: 60

Boil Gravity: 1.043

Efficiency: 70

Mash Thickness: 1.6

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 65 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 12/17/2016 2:08 PM

Notes:

Author:

Chris Hamilton

Boil Size: 22.6 Litres

Boil Time: 60

Boil Gravity: 1.043

Efficiency: 78

Mash Thickness: 3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 18 ° C

Priming Method: Sugar

Priming Amount: 120 g

Creation Date: 9/27/2016 12:51 AM

Notes: Hybrid of several similar recipes. Benefits from conditioning a few months.

http://byo.com/mead/item/1868-irish-red-ale-style-profile
http://www.homebrewtalk.com/showthread.php?t=141086

Author:

Toombstone

Boil Size: 28.6 Litres

Boil Time: 90

Boil Gravity: 1.043

Efficiency: 75

Mash Thickness: 5.102

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 19 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 7/1/2016 9:17 PM

Notes: Brewed using the 20L Braumeister.

Author:

Switz007

Boil Size: 13 Gallons

Boil Time: 60

Boil Gravity: 1.039

Efficiency: 73

Mash Thickness: 1.3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.5

Primary Temp: 68 ° F

Priming Method: .

Priming Amount: N/A

Creation Date: 11/13/2014 7:05 PM

Notes:

Author:

generaltao

Boil Size: 28.4 Litres

Boil Time: 60

Boil Gravity: N/A

Efficiency: 70

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 11/13/2012 8:15 PM

Notes:

Author:

Boil Size: 6 Gallons

Boil Time: 60

Boil Gravity: 1.05

Efficiency: 51

Mash Thickness: 1.54

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 65 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 11/26/2018 9:08 PM

Notes: 1.1L starter 4oz DME
added hefe yeast from last brew
hops straight into primary
no secondary
Final Gravity 1.014
~6 percent
no off smells or flavors
banana juicy fruit smell
used nylon bag as filter on siphon before bottling/kegging
hazy af
force carbed keg to 30psi through dip tube
bottled to 2.7 volume c02 with cane sugar -> 23ish bottles

Author:

Boil Size: 5 Gallons

Boil Time: N/A

Boil Gravity: 1.108

Efficiency: 100

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.25

Primary Temp: 62 ° F

Priming Method: None

Priming Amount: N/A

Creation Date: 9/9/2017 2:23 PM

Notes: Oaked Acerglyn (Sparkling?)
(Maple Mead)

Ingredients
5 gal water
10 lbs Honey
2 packet Red Star Cote des Blancs Yeast
1 Medium Toast American Oak Spiral in secondary
2 x 32 oz Grade A Vermont Maple Syrup

Directions
In a large brew pot, simmer 3 gallons of water.
Remove pot from heat and add 10 lbs honey and 32 oz maple syrup and 3 tsp yeast nutrient. Stir until fully dissolved.
Rehydrate the yeast warm water set aside
Add the must to a 6 gal primary fermenter along with 2 gal cold water. Aerate it, and pitch the yeast when temperature is under 100F
Take OG reading. Mine was: 1.082 g/ml
Seal fermenter with airlock and store in a dark place at a temperature of about 70 degrees.

After 3 days, add 1 tsp yeast nutrient or not and aerate do this again after another 3 days.

After another week, add the remaining 32 oz of maple syrup and aerate.

Wait another week, then with a siphon, re-rack the mead into a sanitized 5 gallon carboy. Add the Oak Spiral at this point

After another 3 weeks, re-rack, then let age for 2 months, with sampling suggested

Bottle still – move totally fermented mead into a sanitized bottling bucket and bottle as you would beer but without the bottling sugar. Cap and store for 4 months in a temperature controlled place. Kitchen is ideal.

Sparkling - Dissolve the corn sugar in 2 cup warm water, add to carboy, and stir lightly.
Fill sanitized bottles and let age for 4 months, storing in the same manner.

Original Recipe: http://meadist.com/making-mead/mead-recipes/sparkling-oaked-acerglyn-maple-mead-recipe/

My Experience:

Heated 3 gallons of water on the stove to 140F added 10 lbs of honey and found that my pot was full and if I went to rapid boil I would have overflowed. I sanitized and poured the stock pots contents into the bucked, added 32 oz of Maple Syrup stirred and waited for cool down. At or around 92F I took a gravity reading which turned out to be 1.084 give or take a bit. Adjusting for temperature, I was not getting the gravity I was looking for I added enough water to make 5 gallons in the bucket and then waited. I pitched the waiting yeast, I used two yeast packets due to messing up with too warm water for the first starter, thought I may have killed some yeast in the too warm water of the flask. Turned out fine however. Bubbling started less than 24 hours later and bubbled strongly for 8 days. I checked gravity again and after 8 days of fermenting at 66-67 degrees the gravity was 1.100??? Obviously my OG was off by some points. I was supposed to be at 1.108 and I think that was probably more like the OG than I calculated it to be. Then I added yeast energizer 2.5 teaspoons and the rest of the maple syrup (another 32 oz) and stirred vigorously.

Pre-new-syrup 1 bubble/18-20 seconds, 24 hours after 1 bubble/6 seconds.
Back on track.

December 5th 1 bubble/5 seconds
Sniffer detects -- the butterscotch is less but a sweet maple smell is clearly there. :)

The Maple mead has been racked off into the secondary with a French Oak curl to continue fermentation. Rate of fermentation has slowed dramatically in the past week from 1 bubble/32 second to twice that now but still she ferments and will likely continue at temperatures of 62 -65F.

Original Gravity: 1.108 g/ml
Current gravity 1.010 at week 5 under fermentation (Dec 29th)
Calculated current gravity= 14.22%

(Projected 15.3 -15.8% ABV)

The rack off date 12/30/2917

I will let the Oak stay on the mead for 6 weeks, then check flavor on approximate date: 1/13/2018.

This is taking a lot longer than the recipe called for.

The third and final racking should happen on 1/13/18 into the glass 5 gallon carboy for clarifying. I have to be very careful and not push this last step. I am thinking maybe two weeks and and bottling the end of January. Allocating most of the batch for still mead and some for carbonation.

Sampled with new wine thief. Tastes of oak and and honey and a hint of maple. Slightly carbonated. Nice balance. Not too acidic as before. Mellowing is a good thing. Tastes like Chardonnay it really does and therefore I decided to halt the fermentation at 15.5% ABV and keep the residual sugars

5 Gallons plus a half gallon went into the carboy on 1/13/2018
FG 1.00
15.5% ABV
Added yeast stabilizer 1/2 teaspoon per gallon to arrest fermentation (Potassium Sorbate)
General color was foggy light yellow.
Waiting for the wine to clarify.
Projected bottling date 1/21/2018

Actual bottling day 2/10/18

"Assuming you are using classic corks, prepare them with a brief soaking in water before insertion if they have been stored for a long time, three months for example, in an open container. Opinions vary about the benefit of adding a bit of standard sulfite solution (two ounces potassium metabisulfite in a gallon of water). Diluting the standard solution to a ratio of about five to one with water softens the corks and eliminates the risk of contamination. In any case soak all corks, even those ordered directly from suppliers. Do not substitute chlorine for sulfite solution; it might lend itself to cork off-flavors. Soaking for an hour or less should suffice. Incidentally, use only new corks that are grade "extra first" or at least the equivalent. Extra first is considered medium grade. There are a lot of inferior corks out there, and these can ruin the wine’s flavor. It is worth the cost to use corks that will protect the wine and allow it to age under ideal conditions."

"After filling, leave the bottles standing cork up for three to five days. This allows the inside pressure to equalize down to normal, so wine won’t push or leak when placed on its side. It also lets the corks dry from the pre-bottling soak and breathe off any residual sulfite. Then store the bottles on their sides or upside down in the coolness of your cellar. After 30 days (okay, we all stretch that a little!), try one bottle to assure yourself all went well. After that, it is up to you when you drink the wine. Almost all wines benefit from three to six months in bottle, some for much longer.

Remember that wine ages in two ways: aerobically, while it is fermenting, being pressed, racked, and prepared for bottling, and anaerobically after bottling, when the myriad subtle chemical changes occur away from the air (other than what is dissolved in the wine at bottling) and produce true bouquet and complexities of flavor. When the wine is best is up to the winemaker, but a little patience is well worthwhile.

If you can creatively bend the rules and develop a method you can live with, by all means do it. Cleanliness is next to Dionysusness!"

I used a carboy siphon for the first time ever and wow this is the total way to go. I have been making beer since 2003 and avoided due to cost and stubbornness this device. Man!

I had to buy corks a case of empty wine bottles, and a corker.

Yield in bottles
17 Wine bottles
3 1/2 Wine bottles
6 Grolsch bottles
1 Bombardier 32 oz
1 12 oz beer bottle full

Wine makers cut maybe 12-14 oz

Usually I go for the stats but here I want to focus on how it tastes.

Being the first Acerglyn and the second ever wine making experiment, I want to savor the flavor and pat myself on the back for making THE oldest beverage in the world, plus a bit of Adirondack Maple Syrup.

Tasting notes:

Color: Light Amber
Clarity: Clear as a bell
Mouthfeel: Good body with ever so slightly effervescence.
Taste: Semi-sweet to dry with Maple and Honey flavors and a bit of tannin.
Finish: Clean, crisp not cloying and with a hint of citrus.

Final ABV: 15%

A new record for me.

Author:

Seaview Brewery

Boil Size: 7 Gallons

Boil Time: 90

Boil Gravity: 1.052

Efficiency: 66

Mash Thickness: 1.3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.0

Primary Temp: 68 ° F

Priming Method: Forced Carbonation

Priming Amount: N/A

Creation Date: 11/27/2015 1:50 AM

Notes: Split the dry hop into two stages: 1) Add the first dry hops after primary fermentation is just about complete (about 1 week). Let this first dry hop addition sit for three days then; 2) Add the second dry hop addition to the primary fermenter for four days (so seven days exposure for the first round of dry hops). Bottle or package immediately on the seventh day. Try to minimize oxygen exposure for best aroma retention. For example, if kegging, purge the keg with CO2 before transferring the wort.

Also, I used this forum from HomeBrewTalk.com on Heady Topper for some direction: http://www.homebrewtalk.com/showthread.php?t=390082

Basically the malt profile is very similar to Heady only scaled down to 7% ABV. The hop profile used HopShot for the 60 minute edition and a Citra/Mosaic combo for all other editions. This is very different from Heady, but is pretty well known to be the hop combo in Focal Banger.

Author:

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.032

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: co2

Priming Amount: 33.62 psi

Creation Date: 6/9/2020 8:01 PM

Notes: Based on similar recipe Posted by Bob Garner on beerrecipies.org

NOTE: water additions based on use of RO water source

Author:

lionman

Boil Size: 28.5 Litres

Boil Time: 60

Boil Gravity: 1.036

Efficiency: 75

Mash Thickness: 3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.5

Primary Temp: 12 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 11/22/2017 3:08 AM

Notes:

Author:

glh11

Boil Size: 8.5 Gallons

Boil Time: 120

Boil Gravity: 1.076

Efficiency: 75

Mash Thickness: 1.25

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.25

Primary Temp: 58 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 2/23/2014 12:08 PM

Notes: I. One month or more before brew day prepare in a 1 pint mason jar makers mark Bourbon or whatever you like and 4 oz. of oak cubes. I also put in 3 Benilla vanilla beans cut up. Soak with oak one month or until they sink.

II. Four days before brew day make a huge starter using Wyeast1728. Use stirplate for best results. Follow favorite software recco.

III. There will be two mashes for this 6.25 gallon batch. The first mash is for kettle carmelaztion only/boil down. As opposed to taking just the first runnings this recipe is using a small separate mash/wort for boildown. Lot of work but delightful. End result will be one quart of caramelized wort.
Recipe:
I do this mash the day before main brew day. Set aside in the refrig.
A. Mash: ph5.4
5 lbs.,simpsons golden promise 2-Row
1/2 oz UK choc 250L
1/2 oz Roasted Barley
1/2 oz east kent goldings
1.50 gal/H2O at 156-58 for one hour.
Sparge for 20 minutes to get 6 qts and reserve balance for main boil. I mashed in a 5 gallon cooler in a bag.

Note: The gravity will be way higher than above recipe, due to the first mash with unfermentable dextrins and long chain sugars. Looking for sweetness/flavors. Hence, the final gravity will also be higher. Check gravity 2-3 times towards the end of primary.

IV. Main mash see receipe above. Mash 1.35 gal/lb at 152F., for two hrs. Add water to maintain heat or recirculate-HERMS/RIMS, Stirring occassionaly, then, Sparge.

V. Combine 1st/2nd mash in boil pot.

VI. Boil for 2 hours further caramelization.
I continue adding reserved wort to the boil over the 2 hours. Sitting in the chair sipping with my hand on the propane valve.

VII. Cool wort to 50F and transfer to fermenter. Put fermenter in an environment of 40-53F ambient. I use a 18 cubic foot chest freezer and a digital controller. Ferment cool/long.

VIII. Take gravity reading

IX. Blast with pure O2 for 1 minute.

X. Add Yeast Wyeast 1728 starter and shake.

XI. 4 hours blast with O2 for one minute

XII 8 hours blast with O2 for one minute

XIII. 12 hours blast with O2 for 30 sec. Yes I actually, get up for this.

VX. Primary fermentation for 3-4 weeks, your call.

XV.Day 7: Take gravity reading
Carefully stir or walk the yeast. Poly stir paddle small end. Be gentle as not to induce oxygen or splash. Get those yeast back to work.

Day 14:Take gravity reading before stirring.
Repeat procedure-walk yeast
Sanitation: Let you stir paddle live in a bucket of star-san next to the fermenter.
Let it now settle for one more week.

Day 21 take gravity reading.
Total of 21 days in fermenter

XVI.Day 21 transfere to secondary. Add oak cubes/two fresh vanilla beans only (not the oaked bourbon).(Save oaked bourbon for secondary if you want to add to it.) Taste after one week and continue to until desired flavor is achieved, then remove oak/beans. Leave in secondary for 3 weeks or desired length at 50-55F. Update: I dropped the temp the last week to 45 ambient: fermenter prob around 49-50.

XVII.Day 42 Bottling bucket. Taste for Bourbon/vanilla. This is for the few who like bourbon/vanilla. I add 12oz. of makers mark and 1/4 cup of (Pure Macormick vanilla 40% ABV) to bottling bucket. If you like more oak/bourbon add some of the bourbon that the oak soaked in. This brew is not for the weak of heart and impatient. Allow to bottle condition for quite some time. This is one hell of a delicious bourbon/vanilla scotch ale for a sipper, cooled to 50F, and drunk in what my wife calls my diva glass. Cheers Good brewing!

Update: Just tasted the first bottle 11/3/14. Still needs to go longer for best flavor. But, no kidding imo it is better than backwoods bastard. I just bought a case for $84 and compared the two. Mine is better hands down. I tweaked the recipe for what I think will be even better next spring when I make it again. (CHANGES)1.I will leave the oak cubes longer;2. Add 1 tbs more vanilla to secondary,and eliminate beans. 3. Increase hop rate-too sweet. 4. Added hops to kettle prep/caramelization batch. 5. Eliminated choc malt 450L and replaced with choc 250L.5. Increased roasted malt.6. Now cooling wort to 48-50F prior to racking to fermenter. Four wks secondary at 45 ambient. Also this ale needs 6 mos plus to age. Worth the wait!
UDATE 2:
Making this recipe this weekend. Adding 1/2 oz of magnum hops at 60 minutes. Beer was not quite bitter enough to match backwoods bastard. Also adding 1/2 cp more of makers mark bourbon.