All-grain Homebrew Beer Recipes | Page 62 | Browse 220,000+ at Brewer's Friend

Author:

thechad

Boil Size: 7 Gallons

Boil Time: 60

Boil Gravity: 1.053

Efficiency: 75

Mash Thickness: 0.8625

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.0

Primary Temp: 66 ° F

Priming Method: Corn Sugar

Priming Amount: 4 oz

Creation Date: 4/23/2014 3:51 AM

Notes: The ABV for this is inflated as it assumes the dark grains labelled as 'late additions' listed will be incorporated into the hot mash. The ABV is actually ~7%.

Using a multi-stage mash method. You could also do a single infusion mash of 20 quarts / 4 gallons at 160 F. Sparge with 3.5 gallons of 170 F.

"Cold steep" the dark grains separately and add to the fermenter when brewing is complete. From the research I've done, to cold steep grains, use a ratio of 2 quarts per pound of room temperature water and let them steep for about 2 hours. The water should be boiled then cooled before steeping the grains and the runoff should also be pasteurized ("boil" it at 170) for a 5 - 10 minutes, then cooled again before adding to the beer in the fermenter. This will help prevent any infections.
Alternatively you can add it to the last 5 minutes of the boil as well, but this may produce some harshness.

For the yeast starter, make a small wort with an OG ~1.036 with 1.25 quart/ .5 cups of DME. It's better to start with more water because you can always boil off some. Too high of a gravity will stress the yeast into actually fermenting whereas a lower gravity wort will give them nutrients to grow, but not focus on fermenting.
http://www.whitelabs.com/beer/homebrew/starter-tips

Author:

liquid bread brewery

Boil Size: 16 Gallons

Boil Time: 90

Boil Gravity: N/A

Efficiency: 70

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 2/19/2012 2:20 AM

Notes: Basil is added 5 minutes until flameout directly to the boil

1/2 minerals added at mash the other half added during the boil after sparging.

Ferment at 64 then let naturally rise into mid to high 70's to finish.

Total water needed is 20 gallons. Mash strike temp is 9 gallons at 172. Sparge at 170 with the other 11 gallons Use Herms to keep mash range at 157 for 75 min.

Author:

emcfarden

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.049

Efficiency: 75

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/21/2019 2:39 PM

Notes: Ferment primary for 7 days or until gravity is at desired FG. Rack beer into secondary directly on the frozen fruit. Sanitize fruit bags before adding and leave fruit whole (no crushing or blending) for sanitation.

Leave in secondary for 1-2 weeks then keg.

Author:

lboaman

Boil Size: 7.5 Gallons

Boil Time: 90

Boil Gravity: 1.046

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 7/4/2015 2:00 PM

Notes:

Author:

rolandblais

Boil Size: 1.2 Gallons

Boil Time: 60

Boil Gravity: N/A

Efficiency: 70

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 78 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 5/6/2013 1:52 AM

Notes: Based on Jalapeño Saison, but minus the jalapeño, and adding 2 lbs of peaches in the secondary. Hoping for a Festina Peche taste-alike...

Author:

Tribe44

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.027

Efficiency: 78

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 50 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 3/5/2015 3:22 AM

Notes:

Author:

Sergio Rivera

Boil Size: 7.25 Gallons

Boil Time: 60

Boil Gravity: 1.036

Efficiency: 75

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.5

Primary Temp: 70 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 3/17/2016 12:57 AM

Notes:

Author:

AndreaOne

Boil Size: 28 Litres

Boil Time: 60

Boil Gravity: 1.045

Efficiency: 77

Mash Thickness: 3.57

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 18 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 9/22/2016 9:08 AM

Notes:

Author:

davejhoward

Boil Size: 8.41 Gallons

Boil Time: 90

Boil Gravity: 1.028

Efficiency: 70

Mash Thickness: 1.25

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 7/22/2018 8:17 PM

Notes: Primary Ferm Temp: 65-68°

Author:

normangeaney@gmail.com

Boil Size: 25 Litres

Boil Time: 60

Boil Gravity: 1.043

Efficiency: 70

Mash Thickness: 2.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 20 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/15/2013 8:53 PM

Notes: Lagring 6 veckor 15 degrees

Author:

SonnyK85

Boil Size: 7.75 Gallons

Boil Time: 90

Boil Gravity: 1.041

Efficiency: 76

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 67 ° F

Priming Method: Corn Sugar

Priming Amount: N/A

Creation Date: 3/26/2017 2:51 PM

Notes: ** YEAST STARTER **

1. Approximately 4 Days prior to Brewing, make 10% DME solution in Erlenmeyer Flask.

MFG Date: ___/___/______
Starter: _____ gm DME / _____ L (per MrMalty.com)

2. Apply Ice Bath until Temperature reaches ~70F.
3. Squeeze 1 packet of WLP570 into DME Solution.
4. Cover with Aluminum Foil + apply to Stir Plate for 18 hours.
5. Refrigerate for ~72 hours prior to brewing.

** MASH **

PRE-HEAT MASH - 2 gal of Boiling Water
PRE-HEAT SPARGE - 2 gal of Boiling Water
(conduct Simultaneously)

Water Volume: 4.3 gallons for 1.5 lb/qt ratio.

1. Prior to heating HLT, check pH of tap water

pH: __________

2. STRIKE WATER: 163F.
3. Prior to adding Grains, add 2mL LA into Strike Water.
4. Add Grains @ 161F.
5. Allow Temperature to fall to 151F prior to closing lid.
6. Check Mash pH ~15 minutes into Mash.

pH: __________

7. Total Mash Time: 60 minutes

FINAL MASH TEMP: __________F
FINAL MASH pH: __________

8. Add 1.5gal of Boiling Water at the end of Mash and stir into solution
9. Begin Vorlauf!

** SPARGE **

1. Add 6.5gal of water + Kettle salts to Pot. Prior to heating, adjust pH to </= 6.0 with Lactic Acid

Lactic Acid addition: __________ mL
Final pH measurement: __________

2. Heat 6.5gal of Water to 175F. Add to Sparge Vessel.
3. Recirculate 4 times prior to collecting wort.
4. Attempt to Sparge over 40 minutes, collect 7.75gal into boil kettle.

** BOIL **

1. Check Pre-Boil Gravity (goal: 1.041) + pH
** NOTE: Make sure to adjust for TEMPERATURE **

PRE-BOIL GRAVITY: __________ @ __________F

2. Adjust Gravity to Goal (1.041)

Adjusted Gravity: __________ (__________ @ __________ F)

PRE-BOIL pH: __________

3. Adjust Pre-Boil pH to: ~5.2 (+/- 0.1)

Final pH measurement: __________
Lactic Acid addition: __________ mL

4. Boil for 90 minutes (goal OG: 1.063)
5. Add Tettnanger Hops @ 60 minutes.
6. Add Sugar @ 15 minutes.
7. Add 1 crushed Whirlfloc tablet @ 5 minutes.
8. Chill wort to ~70F after completion of Boil
9. Auto-siphon wort from Kettle into Mash Cooler with fine mesh bag attached (at the end of auto-siphon)
10. Gravity feed 5.25gal (5gal mark) of wort from Mash Cooler into Catalyst Fermenter
11. Allow Ranco/Chest Freezer to adjust wort temperature to goal starting temp

ORIGINAL GRAVITY: ______________ (goal: 1.063)

** FERMENTATION **

1. Goal Starting Temp: 67F
2. Begin Fermention @ 67F. After ~24 hr of noticeable Fermentation activity, raise the temperature by 1°F / 12-24 hours (max temp: 80F) by the end of 1 week.
3. Allow yeast to flocculate and beer to clear prior to bottling.

** PRIMING **

"carbonate to approximately 3-4 volumes CO2"

Author:

dbrowning

Boil Size: 4.5 Gallons

Boil Time: 60

Boil Gravity: 1.024

Efficiency: 70

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 3/21/2017 2:16 PM

Notes:

Author:

snifter

Boil Size: 35 Litres

Boil Time: 60

Boil Gravity: 1.054

Efficiency: 73

Mash Thickness: 2.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 22 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 7/1/2016 1:07 PM

Notes: First runnings to be boiled separately and reduced to a syrup and added to main boil

Author:

Steven Gallagher

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.053

Efficiency: 75

Mash Thickness: 1.25

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 69 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 9/9/2015 7:41 PM

Notes:

Author:

NDB

Boil Size: 146 Gallons

Boil Time: 60

Boil Gravity: 1.05

Efficiency: 75

Mash Thickness: 1.3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 2/16/2017 11:21 AM

Notes: Mash all grains for 1 hour at 150 degrees.

Sparge at 170 degrees.

One hour boil with hop regimen above.

Chill down to 50F and pitch yeast.

Ferment for about 10-14 days until primary fermentation just finishes.

Diacetyl Rest: Raise beer temp to 62-65F for 2-3 days.

Rack to keg or secondary and start cold-aging process. If possible taper temperature down 5-7 degrees per day from Diacetyl rest to 35F. Cold age at 35F for 5-6 weeks.

Author:

Boil Size: 7 Litres

Boil Time: 60

Boil Gravity: 1.039

Efficiency: 60

Mash Thickness: 4.7

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.5

Primary Temp: 12 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/10/2016 8:27 AM

Notes:

Author:

ryeguy88

Boil Size: 4 Gallons

Boil Time: 60

Boil Gravity: 1.043

Efficiency: 70

Mash Thickness: 1.25

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.5

Primary Temp: 60 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 12/14/2014 7:54 AM

Notes:

Author:

Chricoo

Boil Size: 26 Litres

Boil Time: 75

Boil Gravity: 1.048

Efficiency: 80

Mash Thickness: 4

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 18 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 8/7/2015 6:24 AM

Notes:

Author:

Kevin Zix

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.045

Efficiency: 65

Mash Thickness: 1.25

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 8/14/2016 2:22 PM

Notes:

Author:

tamparob

Boil Size: 6.5 Gallons

Boil Time: 90

Boil Gravity: 1.017

Efficiency: 60

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 70 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 2/13/2018 11:10 AM

Notes: This is a multi-step mash. Mill the grains, then mix with 2 gallons (7.6 L) of 154 °F (72 °C) strike water to reach a mash temperature of 144 °F (66 °C). Hold this temperature for 30 minutes. Raise the mash temperature through infusion of boiling water or recirculating system up to 158 °F (70°C). Hold this temperature for 30 minutes.

Due to the very low enzymatic power of this mash, it is recommended to perform an iodine test to confirm starch conversion before beginning to lauter. If iodine test confirms conversion, then you can raise the mash up to mash out at 172 °F (78 °C). If iodine test is negative, continue to hold at 158 °F (70 °C) until iodine test is clear. Vorlauf until your runnings are clear, then begin sparge. Sparge about 2 gallons (7.6 L) of water then top off your kettle to 6.5 gallons (24.6 L).

Boil for 90 minutes, adding hops according to the ingredient list. After the boil, whirlpool for 5 minutes, then let settle for 5 minutes. Chill the wort to about 65 °F (18 °C) and then pitch yeast and aerate wort.

Once fermentation commences, allow beer to free rise up to 70 °F (21 °C). You can hold this temperature for ten days or until the completion of primary fermentation, whichever is later. Bottle or keg the beer and carbonate to approximately 2.3 volumes.