All-grain Homebrew Beer Recipes | Page 988 | Browse 225,000+ at Brewer's Friend

Author:

bdr0679

Boil Size: 8 Gallons

Boil Time: 60

Boil Gravity: 1.033

Efficiency: 68

Mash Thickness: 1.3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 66 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/14/2016 1:38 PM

Notes:

Author:

RustyBarrelHomebrewing

Boil Size: 8 Gallons

Boil Time: 60

Boil Gravity: 1.038

Efficiency: 60

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 6/29/2022 2:39 AM

Notes: ================================
7/1/2021
brew night last night everything went pretty well. nailed the OG and maybe a little over 5 gal. i did about 6.5 gallons in the mash and then sparged maybe three pitchers of sparge water, at beginning of boil i was at about 7.25 gallons and 1047 pre boil. post boil i was right around 5 gal and 1055, watered down a little bit.

i used perle but ideally i wouldve used some noble american hop. crystal?

================================
6/30/2021
thinking maybe just boil 60 minutes instead of 90? i think a little DMS corn flavor is acceptable here if it should happen to do that.

for yeast kind of stupid i have maybe a half cup slurry but no DME for a starter so i will just pitch the whole slurry and hope its all good

ph calculation mustve been off before, adding some phosphoric acid
================================
6/28/2021

branching from grandma's country lager to Grandpa's. I am not sure grandpa drank any different beer than grandma but for this one we will attempt to stay within the american lager category, whilst adding a little bit of pilsner malt for a little more flavor.

i was going to do legit flaked corn then i thought id keep with the grits but for this lets go for international pale lager and go all malt.

considering carapils but do i want head retention and too much flavor? i think i do but judges may not like.

using legit lager yeast for this.

need to go through hop stash and decide what to use, default evergreen.

================================
11/28/2021
reworking this for round 3. round 2 stunk, had to add DME later, not sure i cooked and mashed the grits long enough. beer turned out infected or something smelled and tasted like wine vinegar.

this time removing the DME boosting the base malt to get to 5.3% although it will be fine if it floats back to 5.0 or 4.8 even. last brew was 59% efficiency, hoping to at least get 62 this time. using my old setup and brewing in parallel to another batch on the GF

Last time was nobility this time trying evergreen. Adjusting hop amounts to stay under 18 ibu.

================================
7/8/2021
Brew day last night, kind of sucked. Tried the brew easy setup for mash and ended up light on efficiency and OG. refractometer said 1035 preboil and about 1038 post boil. then i took less than a gallon of wort and heated up on stove and added 1lb DME. lets see how much that ruins the color. anyway the refrac was still showing low gravity, recalibrated it, and now its saying 1049.

also i forgot about whirlfloc until after the boil so i heated for like 5 extra minutes to give it time to dissolve.

also i forgot to cook the grits before i started the mash so i cooked them during the mash kind of quickly and with less water than instructed, added them about halfway into the mash.

a lot of mistakes here, havent brewed in over a month. also not sure about the brew easy if it was low efficiency because we did not sparge meaning there were leftover sugars in the grain when i was done mash/went to kettle.

i am reading now that we may do better with proper water profile. also i did not take ph reading so unclear if that was an issue. possibly next time we want to try this, we make a straight up pilsner or blonde ale without the grits and use a real water profile built from RO.

also we did not have a proper sparge arm so its possible efficiency was affected by channeling.

================================
7/7/2021
first batch was indeed good the way it was, but altering for todays brew day. low on grits. was gonna just run it but 4.8% is just so low. adding half pound of 2row.

using slightly less acid malt because i feel some of my brews might be too acidic in the end? havent quantified that. pH readings tend to be low.

also going to use some nobility instead of having to hacksaw more of that crystal. adding some to end of the boil because why not....hopefully doesnt pull off too much hop flavor or bitterness in whirlpool (....it shouldnt, with that tiny amount)

not really doing any water chemistry here. going to just run tap and see if i can really tell the difference. fits with the theme of this beer being super easy and cheap as well.

================================
2/8/2021
recipe creation.

malt :
considered using at least a portion of 6row malt which has higher diastatic power; this is/was used for classic (particularly pre-prohibition) american lager to ensure enough enzymes to convert the starch in the corn (which seems to have very low diastatic power). i think this recipe is using relatively low amount of corn adjunct for the style. this is partly because i would like to have a decently malt / body to the beer and also would like to just use my normal 2row base malt and not have to order more stuff from the homebrew store.

corn :
flirted with the idea of using flaked corn, its a little more expensive, for some reason id rather use something from the grocery store. popped popcorn and corn flakes cereal are options but kind more in the direction of a goofy brew. im reading a little about raw corn : it needs gelatinizing before the starches can be freed up enough to convert to sugar in a mash. you'd need to cook it first to do this step. wondering what about thawed frozen corn, maybe thats already been cooked, would that work? anyway this all seems a little goofy still. maybe for another brew. anyway for this i will use a can of instant corn grits. (not convinced this will add any flavor, so really does it even make any sense to use this as opposed to corn sugar? if we're gonna do corn sugar might as well do cane sugar? i guess lets just go with the corn grits since we havent done it before)

it sounds like quick grits we can just drop into the mash without doing a cereal mash beforehand (this is what i did previously with instant rice). (ref: https://www.homebrewtalk.com/threads/quick-grits-confused.431229/)

gravity / abv :
id like this to come to 4.5% but not sure how much the grits will convert so im setting it to 5%abv to give a little slack in case the efficiency is bad.

water :
build from distilled. minor calcium chloride addition. i tried fooling with BF light lager profile but it has this HCO/bicarbonate level that i am not sure with what i am supposed to add to increase the HCO levels to the target. anyway just go with the czech pilsner profile i have used in the past. i looked up some light lager water profiles and they are similar to this.

hops :
gonna use these old frozen wet hops hopefully theyre not bad.

yeast :
going back and forth between 34/70 and lutra. would like to try lutra but i do like the sulfur notes of 34/70 but maybe its not quite appropriate for this beer. also considering some maybe 2007 i do remember it was pretty clean tasting.

Author:

Vader ipa

Boil Size: 7.5 Gallons

Boil Time: 90

Boil Gravity: 1.045

Efficiency: 70

Mash Thickness: 1.4

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 5/4/2021 9:03 PM

Notes: Mid to high 60's for 3 days, then increase to low 70's to finish.

Author:

Wolf Pack Brewing

Boil Size: 37.63 Litres

Boil Time: 90

Boil Gravity: 1.07

Efficiency: 72

Mash Thickness: 3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.25

Primary Temp: 20 ° C

Priming Method: co2

Priming Amount: 1.64 bar

Creation Date: 12/23/2020 4:46 PM

Notes: https://shop.theelectricbrewery.com/pages/kern-river-citra-double-ipa

http://www.thebrewingnetwork.com/post1668/

In this episode of Can You Brew It, Jamil and Tasty attempt to clone Citra Double IPA from Kern River Brewing Company in Kernville, CA. This wonderful craft beer took gold at the Great American Beer Festival in 2011 and has racked up many other awards as one of the best double IPA’s on earth. Tune in and find out if Tasty was able to homebrew this hop monster of a beer.

Needs a 2L Starter using 200g of DME

https://shop.theelectricbrewery.com/pages/kern-river-citra-double-ipa

add 500mg potassium metabisulphite to 20 gallons water to remove chlorine / chloramine (if required).
Water treated with brewing salts to our Hoppy flavour profile: Ca=110, Mg=18, Na=16, Cl=50, SO4=275 (Basically Randy Mosher's ideal Pale Ale numbers with slightly less Sulphate). For complete details on how to adjust your water, refer to our step by step Water Adjustment guide.
1.25 qt/lb mash thickness.
Single infusion mash at 148F for 120 mins.
Raise to 168F mashout temperature and hold for 10 mins.
~90 min fly sparge with ~5.6-5.8 pH water (measured at mash temperature). Collect 13.9 gallons.
Milwaukee MW102 pH meter
MORE INFOBoil for 60 minutes, adding Whirlfloc and hops per schedule.
After boil steep / whirlpool for 20 minutes with the lid on. (No need to stir, steeping is fine. Hop oil extraction is a function of contact time and temperature, not motion).
With the lid still on, cool the wort quickly to 67F (we use a one-pass convoluted counterflow chiller to quickly lock in hop flavour and aroma) and transfer to fermenter.
Aerate well. Pure oxygen from a tank may be used at a rate of 1 litre per minute for 120 seconds per 5 gallons.
Pitch yeast and ferment at 67F (wort temperature). We use modified stainless fermenting buckets in wine fridges.
Due to the high hopping rates and quadruple dry hopping the beer is very susceptible to oxidation. You have to be very careful to minimize all exposure to oxygen in order to preserve the hop flavours and aromas. Even hops themselves can have oxygen caught in their anatomy. Some hints:
If a vessel needs to be opened, purge the headspace with CO2 before closing.
Before adding hops to beer, place them in a tall container and flush with CO2.
Flush target vessels with CO2 before transferring beer. If hops are to be added at the same time (i.e. dry hop #2), add them to the vessel first.
Don't be stingy with CO2! CO2 is cheap. To flush vessels, growlers, kegs we have a separate bare gas line off one of our manifolds with its own shutoff.
Add dry hops #1 once fermentation is nearing completion (i.e. 5 points from terminal gravity) and raise the temperature to 70-72F. We simply turn off the fermenting fridges and allow the beer to naturally rise to room temperature. Steep dry hops #1 for 3 days while fermentation finishes. Assume fermentation is done if the gravity does not change over ~3 days.
Add dry hops #2 to brite tank (we use 5 gallon glass carboys), purge with CO2 to avoid oxygen pickup, then carefully rack in the beer on top of the hops. Allow to steep for 3 days at 70-72F room temperature, gently swirling a few times a day. We do not recommend using hop sacks or other containers as you'll get the best flavour extraction from the hops if you let them roam free. For beers such as this that require multiple dry hop additions, some will dry hop in kegs using stainless steel dry hoppers, tying a piece of unflavoured / unwaxed dental floss to the lid to make it easy to remove (the floss is thin and doesn't impede the seal between the keg and keg lid). We don't recommend this approach as we find that the hops tend to clump together which in turn reduces oil extraction, requiring far too many hops to be used (and more beer lost to absorption).
After 3 days in the brite tank add dry hops #3. Leave previous hops in. Swirl gently a few times a day.
After 6 days in the brite tank add dry hops #4. Leave previous hops in. Swirl gently a few times a day.
After 9 days in the brite tank package as you would normally. We rack to kegs that have first been purged with CO2, and then carbonate on the low side (around 2 volumes of CO2) to minimize carbonic bite and let the hop and malt flavours shine through. We chill the kegs to near freezing while carbonating at the same time in a 6-keg conditioning fridge. After ~1-2 weeks at serving pressure the kegs will be carbonated and ready to serve. Like all hop forward beers this Double IPA is best consumed fresh so feel free to raise the CO2 pressure temporarily to 30-40 PSI to carbonate fast over a 24 period, and then turn back down to serving pressure. Some hop bits will have invariably made their way into the keg during transfer so we use a Hop Stopper Keg Edition filter to ensure that hops do not clog the dip tube and/or end up in the glass. Force carbonating at high pressure and using a Hop Stopper filter allows us to serve this beer 24 hours after kegging. There's no need to wait a few days for any hop bits that made their way into the keg to first settle out.
We do not recommend using finings such as unflavoured gelatin as it may "round off" hop flavours / aromas.

Author:

WRB

Boil Size: 13 Gallons

Boil Time: 60

Boil Gravity: 1.042

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: co2

Priming Amount: 10.16 psi

Creation Date: 5/5/2019 3:40 PM

Notes:

Author:

chris good

Boil Size: 8.5 Gallons

Boil Time: 70

Boil Gravity: 1.037

Efficiency: 75

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 2/21/2019 11:51 PM

Notes:

Author:

Jim2281

Boil Size: 7.5 Gallons

Boil Time: 90

Boil Gravity: 1.061

Efficiency: 35

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 72 ° F

Priming Method: sugar

Priming Amount: 5

Creation Date: 12/29/2018 9:26 PM

Notes:

Author:

ForeverBrewing

Boil Size: 25 Litres

Boil Time: 60

Boil Gravity: 1.042

Efficiency: 75

Mash Thickness: 3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/24/2017 10:01 AM

Notes:

Author:

SAF

Boil Size: 30 Litres

Boil Time: 90

Boil Gravity: 1.066

Efficiency: 70

Mash Thickness: 2.22

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.25

Primary Temp: 24 ° C

Priming Method: Sugar

Priming Amount: 200

Creation Date: 4/24/2016 9:00 PM

Notes: Enhanced Double Decoction Mash (rests at 50, 67 and 77)
- mash in @ 40, rest 5 min
- decoct, heat removed mash to 50, rest 10min
- heat removed mash to 72, rest 15-20min
- boil removed mash for 10-20min
- add in enough boiling mash to hit protein rest @ 50, rest 15-20min
- add in remaining boiling mash to hit 67, rest 60min
- decoct and boil removed mash for 10-20min
- add in removed mash to hit mash out @ 77, rest 15min
- sparge @ 77
- boil 90 min, follow hop/sugar schedule
- pitch yeast @19 let rise to 24 naturally, ferment for 2 weeks
- transfer to secondary, pitch gelatin and cold condition @ 50 for 1 week
- rack to bottling bucket and repitch 1/2 pack 1762 yeast, carbonate to 4 vols in champagne bottles

Author:

Boil Size: 8 Gallons

Boil Time: 60

Boil Gravity: 1.042

Efficiency: 75

Mash Thickness: 3.17

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 2.0

Primary Temp: 50 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/14/2016 9:15 PM

Notes:

Author:

Bakke Brygg

Boil Size: 24 Litres

Boil Time: 90

Boil Gravity: 1.054

Efficiency: 74

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.0

Primary Temp: 18 ° C

Priming Method: Sukkerlake

Priming Amount: 6,5 g sukker/L

Creation Date: 11/16/2013 2:44 PM

Notes: Basert på vinneren i PF under juleølkonkurransen 2012.

Mengden meske- og skyllevann du bør bruke kommer an på utstyret og metoden du brygger med. Som et anslag kan vi si at du kan bruke 16 l meskevann og 12,2 l skyllevann til dette ølet. Noen bryggemaskiner (f.eks. Speidel Braumeister) kan kreve større mengder meskevann. Sjekk alltid manualen på utstyret du bruker.

Mesking på 66 grader i 60 min. Utmesk på 77 grader i 5 min hvis du har mulighet til å øke temperatur i mesken.

Kjøl ned til 17 grader før pitching av gjær.

Gjæring på 18 grader til stormgjæring begynner å avta (typisk etter 3-5 dager). Øk deretter til 20 grader og hold resten av gjæringsperioden (totalt 14 dager). Tørrhumle etter 5 dager.

Gjæralternativer: WLP001, WLP007, WLP051, WLP090, Danstar Nottingham

Author:

Mark F.

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.051

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 70 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/10/2016 4:41 PM

Notes:

Author:

Brew Lab

Boil Size: 17.5 Gallons

Boil Time: 60

Boil Gravity: 1.044

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 68 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 10/26/2015 6:38 PM

Notes: Ferment after lacto/pedio addition with Belle Saison

Author:

Pivarski Klub Bulevar

Boil Size: 75 Litres

Boil Time: 60

Boil Gravity: 1.044

Efficiency: 80

Mash Thickness: 3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.5

Primary Temp: 19 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 10/26/2015 12:17 PM

Notes:

Author:

Mellow Fellow

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.049

Efficiency: 70

Mash Thickness: 1.25

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 68 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 8/22/2015 4:36 PM

Notes: Mash Pale & Munich Malts for 1 Hour.

Add other malts and mash for another Hour.

7 Days in the primary

30 Days Secondary.

Author:

Hoosier2137

Boil Size: 7 Gallons

Boil Time: 90

Boil Gravity: 1.042

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 66 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 6/15/2015 5:51 PM

Notes:

Author:

Stafford's

Boil Size: 6.5 Gallons

Boil Time: 60

Boil Gravity: 1.045

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 2/5/2015 10:29 PM

Notes:

Author:

Wendy Cottrell

Boil Size: 5.5 Gallons

Boil Time: 60

Boil Gravity: N/A

Efficiency: 75

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 5/24/2011 12:43 AM

Notes:

Author:

NateD

Boil Size: 13 Gallons

Boil Time: 90

Boil Gravity: 1.047

Efficiency: 67

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 11/20/2014 6:35 AM

Notes: This will be the first IPA I have done.
Est brew date: 12-5-2014.

Author:

Shane Mac

Boil Size: 15 Gallons

Boil Time: 90

Boil Gravity: 1.055

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.25

Primary Temp: 65 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 10/19/2014 2:37 AM

Notes: Fly Sparging @ 170
Hit target temps and Pre and post boil gravity spot on.
oxygenated with Pure o2 for 2 min.

2nd batch was 10.5 gallons at 1.074, also changed to a brown balanced water profile