All-grain Homebrew Beer Recipes | Page 307 | Browse 225,000+ at Brewer's Friend

Author:

futur3h4wk

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.039

Efficiency: 77

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 5/7/2014 1:58 AM

Notes:

Author:

JohnnyAH

Boil Size: 26 Litres

Boil Time: 60

Boil Gravity: 1.046

Efficiency: 60

Mash Thickness: 2.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 20 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/11/2017 3:57 PM

Notes: Boil start: 7.30

Author:

Ozarks Mountain Brewery

Boil Size: 11.5 Gallons

Boil Time: 120

Boil Gravity: 1.055

Efficiency: 75

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.25

Primary Temp: 60 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 12/17/2014 7:54 PM

Notes: there will be a lot of waste so for best results use a 8 gallon fermenter. My recipe is made for my system that uses pumps,filters,hoses, so scale down for yours if necessary, your going to want to add extra wort for the massive hop losses or you'll end up short

crush semi course to prevent stuck sparge from all the weight and run your pump for 1 to 1.5 hours or 1 hour recirculation and 1 hour slow sparge

whirlpool at 0 after last hop addition until temp drops to 180 then cool

your going to need a 4L starter with 2 yeast to start with

Start with extra water and Boil for 120 minutes or until you reach your normal level.

boil 120 minutes then start your hops and 60 down to 0.

Good Luck, this beer is awesome!

Author:

Boil Size: 7 Gallons

Boil Time: 60

Boil Gravity: 1.044

Efficiency: 68

Mash Thickness: 1.66667

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.25

Primary Temp: 62 ° F

Priming Method: Keg

Priming Amount: N/A

Creation Date: 6/8/2015 7:35 PM

Notes: Add 1 lb honey + 1 qt h20 boiled and cooled at high krausen to raise volume to 5.5 gal

before addition wort will be:
- 1.055 @ 5 gal if 63 % efficiency
- 1.061 @ 5 gal if 70 % efficiency
***these numbers calculated before adding the cereal to recipe

2 boxes has 5.4375 oz of sugar in them according to nutritional info, I'm using that, and dextrose's info to give ppg

Author:

RustyBarrelHomebrewing

Boil Size: 7 Gallons

Boil Time: 60

Boil Gravity: 1.054

Efficiency: 64

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 3/14/2021 4:34 AM

Notes: ===================================
4/2/2021
updating recipe from actual measurements. low on gravity but i think i pulled too much wort and ended up with nearly 6 gallons. mash was strangely in the 5.3 range. ended up adding another 4 oz hops dry hop to the keg.
===================================
3/25/2021
night before brew night
....and im realizing i did not pick up distilled water...doh. looking for an alternate water profile that i can build off of my tap water - and that is assuming the water profile i have for henrico county (from ward labs test sept 2020) is correct! eek.

made a new water profile based on a green flash clone recipe from theelectricbrewery site which they say is basically taken from a randy mosher pale ale water profile. lets see if it works.

===================================
3/17/2021
starting to worry a little about my last IPA, coming from the can its tasting really one dimensional, not bitter enough, too thin, and maybe im paranoid but i detect a slight sour note - wondering if it could be from the acid malt, not being covered up because of the really fermentable grain bill.

for this one i will use phosphoric acid and some crystal malt. adjusting the water chemistry accordingly. considered bumping the warrior too but this brew should have more IBU anyway because sequoia is higher AA than amarillo. its already 90s
===================================
3/13/2021
snapshotting amarillo smash weaddababyitzaboy into this new one to try the sequoia hops. will run it exactly the same. one downside to the amarillo brew was that it couldve had more bitterness. and, i think im starting to understand where people say the west coast can be too one dimensional with only one hop.

could consider adding some light crystal for more malt flavor, or even some reddish crystal along with a more piney hop, more additions for more layered hop bitterness and flavors. maybe in the future but for this time probably just want to let the feature hop shine. its already a blend anyway.

anyway for this brew, the BSG sequoia hops will have slightly higher AA (11 instead of 8ish) and im boosing warrior addition from .73 to .80.

should double check on that salt amount...???

might run it with lutra since i have a bit of it on hand already.

i am also boosting the base malt to get it to 7% so that is taking away from my bitterness effort but it should still be in the 90s IBU. if it still comes out flat we can amp up the hops and bitterness next time.

===================================
1/28/21
brew day. measured 1.062 OG for efficiency of 70%. did double crush on the grain. everything else went smoothly. the water volume calculator was pretty spot on. not sure if i ended with 5.5 gallons or 5 tho.
===================================
1/14/2021
reformulating 10gal cane west recipe into 5 gallon weaddababyitzaboy west coast ipa featuring amarillo hops.
* scratching water profile - was going to switch to ward labs one but its difficult to arrive at the target water profile with that.
* starting with distilled water and building from there.
* swapped out centennial for amarrillo pretty much oz for oz
* adding acid malt for pH
===================================
11092020
just took FG 1005 at 90 deg which equates to 1007 at 70 so turned up attenuation to 86% to match that. ===================================
11/06/2020: brewed last night. everything went well. forgot to take pH and pre boil gravity. it looked like it was boiling slow so i turned it up last 15 minutes of boil, then after chilling i was under volume and OG at like 1.080! topped up to about 10 gallons it appeared still at or above 1065, added more water anyway since i will be having dry hop and trub losses so im estimating 10.5 gallons although it could be more. after all the finagling hit target OG of 1063 on about 10.5 gallons, split one pouch of hothead between two fermentors. lifted brew pot up to table and dispersed wort from there, no pump needed.

the water chemistry tab here is a little wonky i just fixed it to start from my estimated henrico county water to adjust to light colored and hoppy. originally it didnt carry over the profiles from the previous version of this recipe but the water agent amounts are correct. i have an updated sept 2020 water profile from facebook kicking around that i need to add here.
===================================
11/01/2020:
scaling up to 10 gal. i think it will work if i can hit this 68% efficiency. water will take some work. prob will have to treat the mash and sparge water separately - 8 gals for mash and another 6 for sparge. only using 1 lb centennial for 10 gal batch seems light but we will see. i guess west coast uses less? still at 100ibus so it will be decent. could think about using some other hops in flameout and dry hop....cascade...?
===================================
7/14/2020:
just adjusted the water profile in the calculator for 8.5 total gallons treated water and the numbers came out a little better. however a little concerned because the calculator says mash pH will be 5.6 but this recipe says 5.45. i suppose either is fine but the inconsistency is making me nervous that im screwing something up.

going forward i think it will be simpler to use RO and build from there, or try to see if there are basic / minor adjustments i can make to my water to get where i want to go (e.g. just a simple gypsum addition andor campden tab)
===================================
7/13/2020:
adjusting the hop bill based on what i have. increasing ibu from last time (this time using cryo warrior!) decided to try to use all 8oz of centennial i have from a particular Washington state farm via hop of the month. will have increased dry hop.

even though im planning to use hothead (quick turnaround) i noticed in the last brew the beer tasted great initially, then diminished, then peaked later. as such maybe try to ferment for 7 days, dry hop 3 or 4 days in, remove dry hop and cold crash for 7 days before kegging...?
===================================
6/21/2020:

for this 4th attempt at west coast this year, i will be experimenting getting to some target water profile good for west coast ipas.

for now i am going to use the light & hoppy profile built into brewers friend. the chloride cl- is high for the profile (but normal overall) but i think the only way to reduce that is to use RO water so i will just leave it. going to use gypsum (to add calcium) and phosphoric acid to reduce mash pH. we'll see

here is another reference :
https://shop.theelectricbrewery.com/pages/green-flash-west-coast-ipa

===================================
6/21/2020:
this still came out 1.010 but not dry or crisp but rather sweetish. going to take a look at water chemistry next time. (this beer was just brewed using untreated henrico va tap water)

the beer also came out hazy, orangeish. and possibly oxygenated probably because it got roughed up during dry hop / packaging stages as it was my first time dealing with the conical fermentor and spunding valve.

===================================
5/31/2020:
changing grain bill to bump sugar up from 0.5 to 1lb to try to get more dryness. ive read you can do up to 10% sugar. (they say dexrose but im just using table sugar)

also changing hop sched based on the hops i have. i was planning to use some crystal wet hops for this batch but id prefer to use them all at once 2.2 lbs which i think is going to take up a lot of loss, also i am brewing this for the first time on digiboil which may have boiling limitations so im going to fall back and just use some centennial from my hop of the month club. id prefer to use all of one so i can see if i can get the different flavor profiles....
(should i do smaller batches so i can do side by side-ish? if that, ferment in a keg with spunding valve?).
will plan to use the nugget for bittering instead of warrior.....well see.
============================================
5/7/2020:
recipe cloned from "i aint mad atcha". changing recipe in prep to rebrew. simplifying hop varieties. lowering abv a little, removing 15L. aiming for 80 some ibu again. going to mash a little lower? 150. using hothead yeast.

4/7/2020 :
brew day. swapping out the 0.9 magnum 14aa 60 min for 0.5 warrior unknown AA and 0.5 nugget 13.4AA both for 60 mins. this adds up to more IBU than it was with the magnum, but the byo article has it at 77IBU. also i am using some 2 oz 11.4AA 2018 whole hop centennial for the 15 min addition. these hops were leftover from something else, hopefully not oxidized or anything. this way i can add 2 more oz to the dry hop for more flaves. inputting the whole hop AA brought the recipe up to 77IBU. ALSO on a whim i decided to drop a pound of 2row and add .5lb cane sugar to dry it out a little bit. still doing the .5lb 15L (original byo recipe had a pound but last rendition was too sweet). if this all works according to plan i think it will be a nice beer. not sure if i am going to get close to stone. i had a stone ipa the other night. it was too dry and bitter compared to mine. looking for something in between theirs and mine.

3/31/2020:
today i am bumping the magnum and base malt amounts to increase the target IBU and OG to match the BYO article. i am blindly changing the attenuation to match the BYO FG.

this beer was weird. right now it is clear, faint bitterness, decent hop flavor, overall seems close. it is a little too sweet.

this was fermenting at a bit low temperature last month. it was in the fermentation chamber while we were away on vacay but it wasnt plugged in. when i returned it was around 50 or 55. i did cold crash it and kegged it, first week or two it was super hazy and sweet it threw me way off, i thought id confused it with mango maya base beer. it cleared up, hops began to shine more. over time

i had a recipe snafu. unsure the OG. FG is about 1.014. based on 12.5lb 2 row and adjusting attenuation for the FG i got about 6.48 abv on batch 1 (march2020)

8/26/2019 :
adapted from brew your own clone recipe. unclear when this appeared in print. https://byo.com/recipe/stone-ipa-clone/

they boil for 90 minutes (probably to get more bitterness out of less hops, those smarties) they also use perle + magnum but i will just use enough magnum for 60 mins to get up to IBU. the recipe calls for whole hops for dry hop but that will depend on availability / convenience...

Author:

Duguid1080@gmail.com

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.047

Efficiency: 70

Mash Thickness: 1.75

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 65 ° F

Priming Method: co2

Priming Amount: N/A

Creation Date: 2/4/2016 5:58 PM

Notes: Ferment for 3 weeks then secondary. Dry hop during the last 7 days.

Had to substitute Saaz for sterling. On 1/31/21 brew.

Author:

Trub_maker

Boil Size: 8.25 Gallons

Boil Time: 60

Boil Gravity: 1.056

Efficiency: 67

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 82 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 12/11/2015 8:41 PM

Notes: White Labs 530 Abbey Ale Yeast or Wyeast 3787 Trappist High Gravity

Author:

harlaford

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.038

Efficiency: 67

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/18/2015 8:38 PM

Notes: OG: 1.052 approx

Gravity check 1/10 @ 1.03
Gravity check 1/17 @ 1.03

Author:

Mr Norman

Boil Size: 49.5 Litres

Boil Time: 90

Boil Gravity: 1.072

Efficiency: 80

Mash Thickness: 4.6

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 18 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 8/12/2016 2:27 PM

Notes: 90 minute boil. Add soft sugar at beginning of boil. Add syrup at flameout. Chill to 65F (18C). Oxygen for 90 seconds. Ramp primary for 7 days up to 72F (22C). At near-terminal gravity (1.010), rack off primary yeast and drop temp to 60F (16C) for the next 5 days then crash at 50F (10C) until bright. Bottle prime with Simplicity at 32g/gallon. Cellar for 6 months.

Rochefort beers spend six to seven days in primary from 68 (20C) to 73 deg F (23C), three days in secondary at 46 deg F (8C), and 10 days bottle conditioning at 73 deg F (23C), according to BLAM.
http://hbd.org/discus/messages/48727/49605.html?1279817823

Braumeister 50L
Finished volume (L) 45
Grain (kg) 12
Mash Water (L) 42
Mash thickness 3.5
Loss to grain (L/kg) 0.69
Loss to boil (L/hr) 2.9
Boil time (h) 1.5
Top-up Water (L) 6.5
Loss to grain total 8.28
Post Mash Volume 33.72
Loss to boil total 4.35
Sparge water (L) 9.13

Author:

Shølbryggeriet

Boil Size: 53 Litres

Boil Time: 90

Boil Gravity: 1.061

Efficiency: 72

Mash Thickness: 4

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.0

Primary Temp: 20 ° C

Priming Method: Mangrove Jacks Carbonation Drops

Priming Amount: 1 per 0.5l bottle

Creation Date: 2/7/2018 12:16 PM

Notes: 8 packs of yeast, 4 in each fermentor.

Author:

LJvermonster

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.062

Efficiency: 75

Mash Thickness: 1

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.0

Primary Temp: 66 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/7/2014 6:34 PM

Notes: Sparge - Batch Sparge with 4 gallons water.
Fermenting - Primary fermenter only; no carboy.
Dry Hopping - Throw hops in without a bag.

Author:

foichne

Boil Size: 8.5 Gallons

Boil Time: 90

Boil Gravity: 1.038

Efficiency: 72

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/7/2016 6:33 PM

Notes: coffee grounds in bag added to grain bed at 30 min of mash. second addition of coffee in secondary for aging purposes. stout should have very strong coffee tones.

Author:

Boil Size: 26 Litres

Boil Time: 90

Boil Gravity: 14.7

Efficiency: 84

Mash Thickness: 3

Sugar Scale: Plato

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 20 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 11/30/2015 4:56 PM

Notes: datum vareni? kolem konce roku?
predek krasne tahle hutna cokolada, ale strasny zcezovani, nekolikrat vyndano ze scezovacky, prohrabano komplet..cca 6 hodin..nechano na balkone a chmelovar az druhy den..pri 70stupnich dosel plyn, dovareno na dvouplotne, var s temer priktytou poklici, aby byl poradny var,jinak jen male prevalovani. po osmi dnech pridavam coko beans a oak chips, chutna jemne. po ochutnani nejdrive hodne chmelove, cokolada se ztratila, po tzdnu kupodivu dobre, jemneee, prazenost lehka, cokolada...horkost pryc
+ laktoza 15 min var
vanilka jedna 10 min
coko boby trochu pripaleny . 40g. na zacatku supoer cokolada...
oak chips mesic pri 20 stupnich na sekundaru.
chut hoblin hodne citit, ale pivo hodne suche, tenke telo, prazenost az lehka nakyslost... vanilka ani cokolada ci sladkost z laktzy neni citit
24.2. bomba, jemne, chute prostoupily, kyselost je pryc, i prazenost ustoupila, krasne jemne,telo plne, vystupuje vanilka, kokos...

Author:

LaCroix99

Boil Size: 6 Gallons

Boil Time: 60

Boil Gravity: 1.064

Efficiency: 75

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 70 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 9/3/2014 8:31 PM

Notes:

Author:

JonEstrada

Boil Size: 6.83 Gallons

Boil Time: 60

Boil Gravity: 1.048

Efficiency: 75

Mash Thickness: 1.75

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 85 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 10/9/2017 10:39 PM

Notes: Boil for 5 minutes.
Chill to 100°F.
Pre-acidify wort with food-grade lactic acid to get 4.4-4.7 pH, (5mL).
Add 16 oz. of GoodBelly Juice Drink, Mango
Purge the top of Grainfather with CO2
Leave wort at 95°F for 18 hours or until 3.2-3.5 pH.

Boil for 60 minutes.
Chill to ale pitch temp
Pitch yeast
Let ferment for 7 days before taking gravity readings

Author:

Sensing Brewing

Boil Size: 29 Litres

Boil Time: 60

Boil Gravity: 1.039

Efficiency: 80

Mash Thickness: 2

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 28 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 2/24/2018 8:42 AM

Notes:

Author:

dpatrickv

Boil Size: 7 Gallons

Boil Time: 60

Boil Gravity: 1.031

Efficiency: 70

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 68 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 7/12/2015 1:21 PM

Notes: 2nd place in the Lincoln, NE Sowers Cup competition.

Score of 39

Author:

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.048

Efficiency: 75

Mash Thickness: 1.25

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.5

Primary Temp: 76 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 7/8/2018 3:36 PM

Notes:

Author:

Bubba Wade

Boil Size: 3.5 Gallons

Boil Time: 60

Boil Gravity: 1.039

Efficiency: 75

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.0

Primary Temp: 64 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/4/2019 9:45 PM

Notes:

Author:

Brew by Andre

Boil Size: 24 Litres

Boil Time: 60

Boil Gravity: 1.05

Efficiency: 70

Mash Thickness: 5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 20 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 8/8/2016 8:22 PM

Notes: Roast your cocoa nibs and let rest in whisky for a few days. Rack to secondary after about 5 - 7 days and "dry hop" with your cocoa nibs / whisky solution.

Read about No Sparge here:
http://brulosophy.com/2014/08/27/no-sparge-brewing-with-a-beersmith-tutorial/

*Optional*
Cold crash beer until it is below 10°C (50°F) and add gelatin solution. Continue cold crash to 0°C (32°F) and let sit for about 32 hours.