Homebrew Beer Recipes | Page 847 | Browse 310,000+ at Brewer's Friend

Author:

MarylandBrewer

Boil Size: 7 Gallons

Boil Time: 60

Boil Gravity: 1.031

Efficiency: 63

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: BIAB

Pitch Rate: 0.75

Primary Temp: 68 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/26/2016 2:23 AM

Notes: This brew is part of our 55-gallon barrel program. 10 different brewers, 1 recipe, 1 barrel. we will solera this lambic, infected as it may be, and start to draw it down in spring 2017. will brew again to top off the barrel

Author:

rolandblais

Boil Size: 1.6 Gallons

Boil Time: 60

Boil Gravity: 1.041

Efficiency: 72

Mash Thickness: 1.7

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 70 ° F

Priming Method: MapleSyrup

Priming Amount: .5 oz

Creation Date: 2/28/2020 7:40 PM

Notes: This is a guesstimate, from a kit. Malt Bill is from their "Every Day IPA" recipe, with adjuncts noted.

Recipe kit:
https://brooklynbrewshop.com/collections/beer-making-mixes/products/milkshake-ipa-beer-making-mix

Instructions:
https://brooklynbrewshop.com/pages/instructions-milkshake-ipa

Pre-Brew: Sanitize
Sanitization is important, but it's nothing scary. When brewing, keep everything clean so that you give what you're brewing its best chance to succeed. So when preparing for brew day, wipe any crumbs off the counters. Move any clutter that might be in your way. Read through the rest of the instructions (at least through fermentation) so that you know what to expect. And have fun!

Dissolve half of your sanitizer packet with a gallon of water in a container. Save the second half for when you bottle.
Soak everything you are going to use, rinse with water, and let air dry on some paper towels. If it isn’t totally dry when you are ready to start don’t worry.
Keep the extra sanitizer in a container for now. Chances are you’ll want to re-sanitize something later.
Additional Ingredients Needed:

3 Tablespoons Honey
Ice
1 vanilla bean (optional)

1: The Mash
During The Mash, you're extracting all the sugars, color and flavor you can from grain. You're basically just steeping grain in hot water. It's a lot like making oatmeal.

Heat 2.5 quarts (2.4 liters) of water to 160°F (71°C).
Add grain (This is called “mashing in.” Take note of jargon. Or don’t).
Mix gently with spoon or spatula until mash has consistency of oatmeal. Add water if too dry or hot. Temperature will drop to ~150°F (66°C).
Cook for 60 minutes at 144-152°F (63-68°C). Stir every 10 minutes, and use your thermometer to take temperature readings from multiple locations.
You likely don’t need to apply heat constantly. Get it up to temperature, then turn the heat off. Monitor, stir, and adjust accordingly to keep in range.
After 60 minutes, heat to 170°F (77°C) while stirring constantly (“Mashing Out”).

2: The Sparge
If you're familiar with brewing coffee, you should have an idea of how The Sparge works. During The Sparge, you put the grain in a strainer and pour hot water over it to draw out all those sugars you created during The Mash.

Heat additional 4 quarts (3.8 liters) of water to 170°F (77°C). (If possible, start this during The Mash to save time.)
Set up your “lauter tun” (a strainer over a pot).
Carefully add the hot grain mash to the strainer, collecting the liquid that passes through.
This liquid is called “wort” (pronounced “wert”). It will be your beer.
Slowly and evenly pour 170°F (77°C) water over the mash to extract the grain’s sugars.
You want to collect 6 quarts (5.7 liters) of wort. You will lose about 20% to evaporation later on, so you want to start with a bit more than you’ll end with.
Re-circulate wort through grain once.

3: The Boil
The Boil is probably the easiest step to understand because it's as simple as it sounds. During this step, you're bringing your wort to a low, rolling boil and keeping it there for a period of time while adding things like hops or spices. It's a lot like cooking a soup or stock in that you'll add heartier or bittering ingredients toward the beginning and more delicate and aromatic ingredients toward the end.

In a pot, heat wort until it boils.
Keep boiling until you’ve hit the “hot break” (Wort will foam - you may need to reduce heat slightly so it doesn’t boil over.)
Stir occasionally. All you want is a light boil – too hot and you lose fermentable sugars and volume.
The boil will last 60 minutes. Start your timer and add in the rest of the ingredients at these times:

Add Columbus Hops at the start of the boil.

At 60 minutes turn off heat. Add Lactose Sugar and 1/3 Mandarina Bavaria Hops

Twenty percent of the wort will have evaporated in this step leaving you with 1 gallon (3.8 liters) of wort. If your boil was a bit high, the surface area of your pot extra large, or you brewed on a really hot day, you may have less than the full amount. Don’t worry – you just reduced your beer a bit too much, but you can add more water in the next step.

4: Fermentation
This is when your beer actually becomes alcoholic. During Fermentation, your jugs should sit somewhere out of the way (and out of direct sunlight) while ale yeast turns sugar into alcohol.

Place brew pot in an ice bath until it cools to 70°F (21°C).
Once cooled, place strainer over funnel and pour your beer into the glass fermenter. Yeast needs oxygen. The strainer helps aerate your wort and clarify your beer (as well as catch any sediment from going into the fermenter). Add tap water to bring wort up to 1 Gallon mark if level is low.
“Pitch” yeast. (Toss the whole packet in.)
Shake aggressively. You’re basically waking up the yeast and getting more air into the wort.
Attach sanitized screw-top stopper to bottle. Slide rubber tubing no more than 1” (2.5 cm) into the stopper and place the other end in small bowl of sanitizer solution. You’ve just made a “blow-off tube”. It allows CO2 to escape.

Let sit for two or three days or until vigorous bubbling subsides. This is when fermentation is highest. You may notice bubbles and foam at the top of the beer. After bubbling calms down, clean tubing and ready your airlock.

Open your fermenter and drop 1/2 remaining Mandarina Bavaria Hops into your beer. This is called dry hopping and will give your beer intense hop flavor.
Sanitize, then re-assemble airlock, filling up to line with sanitizer.
Insert airlock into hole in stopper.

1 week later drop remaining hops to your fermenter as a second dry hop. You can also add 1 vanilla bean split down the middle for added flavor.

Sanitize, then re-assemble airlock, filling up to line with sanitizer.
Insert airlock into hole in stopper.

Keep in a dark place at room temperature for two weeks without disturbing other than to show off to friends. (If beer is still bubbling, leave sitting until it stops.)

In the meantime, drink beer with self-closing swing tops, or ask for empties at a bar that has some. If you have a bottle capper and caps, you can save two six packs of non-twistoff beers instead.

5: Bottling (2 Weeks Later)
Once your beer's in bottles, it carbonates naturally with the help of just a little extra sugar. It wakes up your ale yeast (that went dormant during fermentation) to create just enough bubbles for some nice fizz.

Thoroughly rinse bottles with water, removing any sediment.
Mix remaining sanitizer with water.
Fill each bottle with a little sanitizer and shake. Empty after two minutes, rinse with cold water and dry upside down.

Dissolve 3 tablespoons maple syrup with 1/2 cup water. Pour into a sanitized pot. You will be siphoning your beer into the same pot in the next steps.
Carbonation comes from adding sugar when bottling, so if you filled your jug with less than the full gallon in the last step, use less maple syrup when bottling. Using the full amount can result in your beer being over-carbonated.

Siphoning (It all happens pretty fast. You may want to practice on a pot of water a few times.) To see it in action first, watch the How to Bottle video at brooklynbrewshop.com/instructions.

A. Attach open tubing clamp to tubing.
B. Fill tubing with sanitizer.
C. Attach sanitized tubing to the short curved end of your sanitized racking cane. Attach the black tip to the other end - it will help prevent sediment from getting sucked up. It will probably be a snug fit, but you can get it on there.
D. Pinch tubing clamp closed.
E. Remove screw-cap stopper and place racking cane into jug, just above the sediment at the bottom (“trub”).
F. Lower end of tubing not connected to racking cane into sink. Suction will force beer up and through the racking cane and tubing. Open tubing clamp, let sanitizer flow into sink until beer just starts to flow out of the tubing, then clamp shut. Open clamp on tubing, allowing beer to flow into pot with sugar solution. Tilt jug when beer level is getting low, but be careful in not sucking up the trub.
Siphon beer from pot into bottles, pinching tube clamp to stop flow after each bottle.

Close bottles.
Store in a dark place for 2 weeks.

6: Enjoy (Two Weeks Later)
You did it! You made beer.

Put beers in the fridge the night before you drink them.
Drink. Share with friends if you’re the sharing type.

Author:

Stvervaag

Boil Size: 29 Litres

Boil Time: 60

Boil Gravity: 1.058

Efficiency: 75

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: BIAB

Pitch Rate: N/A

Primary Temp: 20 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 8/27/2018 7:47 PM

Notes: 1,5 l starter.

Author:

gozer

Boil Size: 26 Litres

Boil Time: 30

Boil Gravity: 1.061

Efficiency: 70

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: BIAB

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 2/21/2018 7:16 PM

Notes:

Author:

Luke & Eric's Brewing

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.064

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 75 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 12/10/2017 8:02 PM

Notes: E

Author:

Back of the Passage Brewery

Boil Size: 31 Litres

Boil Time: 45

Boil Gravity: 1.047

Efficiency: 61.5

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: BIAB

Pitch Rate: N/A

Primary Temp: 21 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 7/10/2017 8:01 AM

Notes: 23/7/17
- Dry pitched x2 yeast
- Bubbled hard for almost 2 weeks
4/8/17
- Dry hoped
5/8/17
- SG 1012, strong lemon citrus flavours upfront
- Cold crashed to 0.5C
7/8/17
- 1 tsp gelatin added to 200ml of water
28/8/17
- Really poor head retention and flat as hell, quite sweet. Lots of lemon citrus in the aftertaste.

Author:

Claxtown

Boil Size: 6 Gallons

Boil Time: 60

Boil Gravity: 1.088

Efficiency: 70

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: Partial Mash

Pitch Rate: 1.0

Primary Temp: 70 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 2/8/2017 9:49 PM

Notes:

Author:

Scribble

Boil Size: 4 Gallons

Boil Time: 60

Boil Gravity: 1.113

Efficiency: 72

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: Partial Mash

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 10/31/2013 8:37 PM

Notes:

Author:

Boil Size: 35 Litres

Boil Time: 90

Boil Gravity: 1.054

Efficiency: 67

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: BIAB

Pitch Rate: N/A

Primary Temp: 21 ° C

Priming Method: Sugar

Priming Amount: 100

Creation Date: 10/8/2015 1:08 PM

Notes:

Author:

seankelly789

Boil Size: 6 Litres

Boil Time: 60

Boil Gravity: 1.29

Efficiency: 35

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: Partial Mash

Pitch Rate: 1.0

Primary Temp: 18 ° C

Priming Method: DME

Priming Amount: 60

Creation Date: 9/16/2015 12:51 PM

Notes:

Author:

Gary Griffith

Boil Size: 5 Gallons

Boil Time: 60

Boil Gravity: N/A

Efficiency: 75

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: Partial Mash

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 3/15/2011 10:15 PM

Notes: I'll brew this on 4/9 so I can get an IPA over to the Wisconsin State Fair for May 14 judging. It has to be in the bottles by April 27, so I'll try to goose up the fermentation with my new aeration stone.

Author:

Stevobrews10000

Boil Size: 26 Litres

Boil Time: 60

Boil Gravity: 1.046

Efficiency: 74

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: BIAB

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/13/2016 1:09 AM

Notes: 15g gypsum 10g cal chlor 10g epsom
Removed all hot break
7g brewbrite at whirpool for 10
Used hop spider 1st time
Hop bag in cube
Into fermenter 08-05-16

Author:

John F McGuire

Boil Size: 8.5 Gallons

Boil Time: 90

Boil Gravity: 1.069

Efficiency: 68

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.0

Primary Temp: 68 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/17/2016 5:12 PM

Notes: Chocolate extract added during bottling.

Author:

Brett

Boil Size: 3 Gallons

Boil Time: 60

Boil Gravity: 1.18

Efficiency: 35

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: Extract

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 12/6/2016 9:08 PM

Notes: Place the grains in a muslin sack and then steep the grains in 1.5 gallons of water at 160°F (71.1°C) for 30 minutes. Take out the grains and hold them over the kettle allowing the remaining water to drip back into the kettle. Do not squeeze the grains. Squeezing the grains could result in bitter tannin extraction. Top up your brew kettle to 3 gallons and bring to a rolling boil (If possible, top up to 7.7 gallons and conduct a full boil). Stir in the malt extracts and bring kettle to a rolling boil. Boil for 30 minutes. Add 1.6 oz of Kent Goldings hops and allow to boil for 50 more minutes. Be careful when adding hops as you may encounter a boil over during the first hop addition. With 10 minutes left in the boil, add 0.5 oz of Kent Goldings. Allow the wort to cool and then pitch the yeast around 65° F (18° C). Ferment around 65° F (18° C). When fermentation is finished, carbonate the beer to approximately 2 to 2.5 volumes of CO2. A period of cold conditioning for several months will improve this beer.

Author:

SAF

Boil Size: 25 Litres

Boil Time: 60

Boil Gravity: 1.047

Efficiency: 68

Mash Thickness: 2

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.0

Primary Temp: 16 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/11/2017 11:50 AM

Notes:

Author:

Sakiškių alus

Boil Size: 540 Litres

Boil Time: 60

Boil Gravity: 1.051

Efficiency: 75

Mash Thickness: 2.7

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 6/28/2015 6:26 PM

Notes:

Author:

Crookedeyeboy

Boil Size: 41 Litres

Boil Time: 105

Boil Gravity: 1.028

Efficiency: 70

Mash Thickness: 2.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 20 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 5/20/2015 12:59 PM

Notes: Page 331 of ASB's

Author:

Christopher S. Witzel

Boil Size: 12 Gallons

Boil Time: 90

Boil Gravity: N/A

Efficiency: 75

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 11/11/2011 6:31 AM

Notes:

Author:

BCole

Boil Size: 6.5 Gallons

Boil Time: 60

Boil Gravity: 1.036

Efficiency: 90

Mash Thickness: 1.25

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 68 ° F

Priming Method: co2

Priming Amount: N/A

Creation Date: 12/14/2019 7:20 PM

Notes:

Author:

gadrael

Boil Size: 7.06 Gallons

Boil Time: 60

Boil Gravity: 1.04

Efficiency: 70

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: BIAB

Pitch Rate: 0.35

Primary Temp: 65 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 7/15/2014 2:37 AM

Notes: