All-grain Homebrew Beer Recipes | Page 1018 | Browse 220,000+ at Brewer's Friend

Author:

Mitch Wineman

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.036

Efficiency: 72

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 68 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 7/25/2017 2:11 PM

Notes:

Author:

Williamchjacobs

Boil Size: 14.75 Litres

Boil Time: 60

Boil Gravity: 1.041

Efficiency: 76

Mash Thickness: 3.65

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: dextrose

Priming Amount: 73.2 g

Creation Date: 10/30/2022 7:38 PM

Notes: The color is considerably darker. Two decoctions: Decoction 1 for 20 minutes (1 liters) and decoction 2 for 10 minutes (1 liter).

Reduced the original boil from 90 minutes to 60 minutes. Also adjusted the gain as the effiency was 76% vs. originally planned 70%.

Had to add back 3 liters of water to hit 1.050 specific gravity after boil.

Einmaischen in 8,5 liter wasser 37°C
3 liter Dickmasche zeihen 10 min. bei 72°C rasten & 10 min 100°C
Zu brühen erbit 53°C anschließsen 10 min. rasten
2,4 liter Dickmasche ziehen, 10 min bei 72°C rasten & 10 min 100°C
Zu brühen ergibt 63°C anschließend 30 min rasten
2,9 liter Disckmasche ziehen 10 min. bei 72°C rasten & 19min 100°C
Zu brühen ergibt 72°C anschließend 30 min rasten
Abmaischen bei 72°C

A lager fermentation consists of these 3 phases:

primary fermentation : main fermentation of the fermentable extract. The bulk of the CO2 and alkohol are created here. Chill the beer to at/below pitching temperature, 9–10°C.
Pitch the yeast and wait 24–48 hours for fermentation to begin. Maintain the temperature for two weeks.

maturation : the yeast is allowed to clean up some of its byproducts like diacetyl (butterscotch flavor) and acetaldehyde (green apple flavor). After active fermentation slows, raise the temperature over several days to 18°C. Allow the beer to sit there for two or three days to clean up the diacetyl.

cold stabilization (lagering) : the low temperature causes haze forming proteins and polyphenols come out of solution and drop out of suspension. There is also a mellowing of flavors and some formation of esters happening. The latter becomes only significant after more than 12 weeks. Lower the temperature to 1°C to 2°C by reducing temp. 1°C per day.

Author:

Wolf Pack Brewing

Boil Size: 37.25 Litres

Boil Time: 90

Boil Gravity: 1.05

Efficiency: 72

Mash Thickness: 3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.5

Primary Temp: 12 ° C

Priming Method: co2

Priming Amount: 1.84 bar

Creation Date: 6/22/2021 9:37 AM

Notes: Fermentation temp: 50°F (10°C) 2 weeks. 32°F (0°C) 12 weeks.

Author:

Vader ipa

Boil Size: 7.5 Gallons

Boil Time: 90

Boil Gravity: 1.045

Efficiency: 70

Mash Thickness: 1.4

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 5/4/2021 9:03 PM

Notes: Mid to high 60's for 3 days, then increase to low 70's to finish.

Author:

Boil Size: 30.95 Litres

Boil Time: 90

Boil Gravity: 9.4

Efficiency: 75

Mash Thickness: N/A

Sugar Scale: Plato

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 16 ° C

Priming Method: sucrose

Priming Amount: 56.3 g

Creation Date: 4/25/2020 6:59 AM

Notes: yeast:

Gozdawa Old German Altbier 9 - OGA9

16-17°C °C

or

MJ Californian Lager M54
18-20°C °C

carbonisation:

5 g/l

Author:

AlleyCAt

Boil Size: 5 Gallons

Boil Time: 60

Boil Gravity: 1.033

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 12/17/2019 7:33 AM

Notes:

Author:

ChicoBrewer

Boil Size: 8.5 Gallons

Boil Time: 90

Boil Gravity: 1.044

Efficiency: 80

Mash Thickness: 1.3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.0

Primary Temp: 58 ° F

Priming Method: co2

Priming Amount: N/A

Creation Date: 6/29/2019 3:10 AM

Notes: https://byo.com/article/bohemian-pilsener-style-profile/

Bohemian Pilsener
(5 gallons/19 L, all-grain)
OG = 1.056 (13.9 °P) FG = 1.016 (4.2 °P)
IBU = 40 SRM = 4 ABV = 5.3%

Ingredients:
10.75 lb. (4.8 kg) Durst continental Pilsner malt (or similar) 2 °L
0.75 lb. (340 g) Briess Carapils® malt (or similar) 2 °L
4.83 AAU Czech Saaz hops (1.38 oz./39 g for 3.5% alpha acid) (60 min)
5.8 AAU Czech Saaz hops (1.67 oz./47 g for 3.5% alpha acid) (30 min)
2.9 AAU Czech Saaz hops (0.83 oz./24 g of 3.5% alpha acid) (10 min)
2.9 AAU Czech Saaz hops (0.83 oz./24 g of 3.5% alpha acid) (0 min)
White Labs WLP800 (Pilsner Lager), Wyeast 2001 (Urquell) or Fermentis Saflager S-23 yeast

Step by Step
Mill the grains and dough-in targeting a mash of around 1.5 quarts of water to 1 pound of grain (a liquor-to-grist ratio of about 3:1 by weight) and a temperature of 154 °F (68 °C). Hold the mash at
154 °F (68 °C) until enzymatic conversion is complete. Infuse the mash with near boiling water while stirring or with a recirculating mash system raise the temperature to mash out at 168 °F (76 °C). Sparge slowly with 170 °F (77 °C) water, collecting wort until the pre-boil kettle volume is around 6.5 gallons (25 L) and the gravity is 1.044 (10.9 °P).

The total wort boil time is 90 minutes, which helps reduce the SMM (S-methyl methionine) present in the lightly-kilned Pilsner malt and results in less DMS (Dimethyl Sulfide) in the finished beer. Add the first hop addition with 60 minutes remaining in the boil. The other hop additions are at 30, 10, and zero minutes left in the boil. Add Irish moss or other kettle finings with 15 minutes left in the boil.

Chill the wort to 50 °F (10 °C) and aerate thoroughly. The proper pitch rate is 20 grams of properly rehydrated dry yeast, four packages of liquid yeast or one package of liquid yeast in a
9-liter starter.

Ferment around 50 °F (10 °C) until the yeast drops clear. With healthy yeast, fermentation should be complete in two weeks or less, but don’t rush it. Cold fermented lagers take longer to ferment than ales or lagers fermented at warmer temperatures. If desired, perform a diacetyl rest during the last few days of active fermentation.

Rack the finished beer to a keg and force carbonate or rack to a bottling bucket, add the priming sugar, and bottle. Target a carbonation level of 2 to 2.5 volumes.

A month or more of cold conditioning at near freezing temperatures will mellow some of the flavors and improve the beer. Serve at 43 to 46 °F (6 to 8 °C).

Author:

Yeast_Whisperer

Boil Size: 8 Gallons

Boil Time: 90

Boil Gravity: 1.037

Efficiency: 72

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 52 ° F

Priming Method: Forced Carbonation

Priming Amount: Keg with 14.89 PSI

Creation Date: 12/14/2018 9:10 PM

Notes: Brewed on 10 Jun 2018
OG: 1.1.054
FG: 1.014
Attenuation: 73.2%
ABV: 5.3%

Compared with Pilsner Urquell
- Color is nearly spot-on
- Head is whiter than Urquell
- Urquell has more hop aroma and flavor
- Otherwise nearly identical !!

Scored 39 at the 2018 Maryland State Fair (1st Place)

Recipe Source: http://www.theelectricbrewery.com/forum/viewtopic.php?t=26537
Fast Lager Method Source: http://brulosophy.com/methods/lager-method/

Yeast Starter = three steps to yield 451 billion cells (starting with 42 billion cells based on age of package)
Step 1 = 0.7 L, Step 2 = 1.0 L, Step 3 = 1.5 L

Ingredients:
Weyerman floor malted Pilsner malt

Starter:
- Use a two step starter (start a week before brew day) -- target ~ 416 billion cells
- Step 1: ~ 1 liter
- Step 2: Decant, then ~ 1.6 liters
- Decant before pitching

Mash:
- pH target is 5.3 at room temp (or 5.05 at mash temp)
- pH Adjustment Notes
- To derease pH by 0.1, add 0.8 ml of 88% lactic acid
- To increase pH by 0.1, add 0.5 grams of pickling lime

Boil Timer Settings:
nE=4, AD=10, T1=90, T2=20, T3=15, T4=5

Fermentation:
- Chill wort to 50 degrees
- Oxygenate (lots of oxygen -- at least 90 seconds)
- Ferment at 52 degrees until 50% attenuation (based on fast ferment FG) is reached (4-7 days)
- Remove temperature probe from thermowell and attach to small volume of liquid (to measure ambient air temp)
- Disconnect plug from cooling side of temperature controller
- Slowly raise air temp from 52 degrees to 67 degrees over 36 hours (5 degrees per 12 hours). See STC-1000+ settings below.
- Keep air temp at 68 degrees until fermentation is complete and the yeast clean up after themselves ( 4-10 days)

- Test for Diacetyl and acetaldehyde -- see https://www.winning-homebrew.com/diacetyl-test.html

- When FG is stable and no diacetyl or acetaldehyde is detected,
- Reattach temperature probe from controller into thermowell
- Attach CO2 tank and add 1-2 pounds of pressure
- Set up a separate thermometer to monitor temperature of the beer
- Slowly decrease temperature from 68 degrees to 32 degrees over 72 hours (0.5 degrees per hour), then see next step. See STC-1000+ settings below.
- When beer temp is below 50 degrees, add prepared gelatin fining
- 1 tsp gelatin in 1/2 cup water,
- Microwave it in short (7 second) bursts until it reached 145-150°F, stirring with the end of a thermometer between each burst.
- Let beer clarify for a few days, then package

STC-1000+ Settings for Fermentation Ramp Up:
SP0: 52°
dh0: 36 (36 hour free-rise/ramp-up)
SP1: 68°
dh1: 0

STC-1000+ Settings for Fermentation Ramp Down:
SP0: 68°
dh0: 72 (3 day ramp-down)
SP1: 32°
dh1: 0

Packaging:
Keg:
- Transfer beer to keg
- Attach CO2 and set to PSI needed to carbonate to 2.5 volumes of CO2 @ 32 degrees
- Let beer condition at 32 degrees for a couple weeks
- Tap the keg
Bottles:
- Sanitize bottles
- Add a coopers carb drop to each bottle
- Add beer and cap each bottle
- Put bottles in area of stable ambient temperature of around 70 degrees for a couple weeks (to carbonate the beer)
- Let beer condition at refrigerator temps (32-36 degrees) for another 1-2 weeks

15 min mash pH = 5.15
added 0.4g pickling lime
10 min mash pH = 5.28
after mach, iodine test = negative

Forced ferment finished at 1.014

Author:

onlyamos

Boil Size: 14 Gallons

Boil Time: 60

Boil Gravity: 1.044

Efficiency: 75

Mash Thickness: 1.33

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 70 ° F

Priming Method: co2

Priming Amount: N/A

Creation Date: 4/19/2018 3:53 PM

Notes: Step by Step

Mill the grains (including the flaked grains, but excluding the rice hulls). Mix the rice hulls into the grain post milling and dough-in targeting a mash of around 1.5 quarts of water to one pound of grain (a liquor-to-grist ratio of about 3:1 by weight) and a temperature of 122 °F (50 °C). Hold the mash at 122 °F (50 °C) for 15 minutes then raise the temperature over the next 15 minutes to 154 °F (68 °C). Hold until conversion is complete, about 60 to 90 minutes. Raise the temperature to mash out at 168 °F (76 °C). Sparge slowly with 170 °F (77 °C) water, collecting wort until the pre-boil kettle volume is around 6.5 gallons (25 L) and the gravity is 1.039 (9.7 °P).

The total wort boil time is 90 minutes, which helps reduce the SMM present in the lightly-kilned Pilsner malt and results in less DMS in the beer. Add the bittering hops with 60 minutes remaining and the spices with five minutes left in the boil. Do not bother with Irish moss or other kettle finings. Chill the wort rapidly to 68 °F (20 °C), let the break material settle, rack to the fermenter and aerate thoroughly.

Pitch ten grams of properly rehydrated dry yeast or use two liquid yeast packages. Alternatively make a 2 qt. (2 L) starter using one package of liquid yeast. Begin fermentation at 68 °F (20 °C) slowly raising temperature to 72 °F (22 °C) by the last one-third of fermentation. When finished, carbonate the beer to approximately 2.5 to 3 volumes of CO2.

Author:

c c b

Boil Size: 120 Gallons

Boil Time: 60

Boil Gravity: 1.07

Efficiency: 80

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/24/2018 8:09 PM

Notes:

Author:

Hound of Culann

Boil Size: 6 Gallons

Boil Time: 60

Boil Gravity: 1.057

Efficiency: 74

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.0

Primary Temp: 68 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/18/2015 6:58 PM

Notes: Recipe perfect for 3-Gln mini kegs.

Don't be afraid of the Summit bittering hops... they're way smoother than the IBUs suggest, and add awesome tangerine flavor accenting the pine and grapefruit pith flavors imparted by the whirlpool hops.

Inspired by Hop Stoopid.

Author:

h82luz2000

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.049

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.5

Primary Temp: 65 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 3/18/2017 10:08 PM

Notes:

Author:

liriodendron

Boil Size: 28.4 Litres

Boil Time: 60

Boil Gravity: 1.067

Efficiency: 70

Mash Thickness: 2.9

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: 18 ° C

Priming Method: dextrose

Priming Amount: 180g

Creation Date: 1/25/2017 2:03 AM

Notes: Mash: Add Chocolate malt in last 15 min of mash.

Author:

RoundKid

Boil Size: 13.5 Gallons

Boil Time: 60

Boil Gravity: 1.051

Efficiency: 80

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.5

Primary Temp: 48 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 12/27/2016 4:38 PM

Notes:

Author:

Jandira

Boil Size: 110 Litres

Boil Time: 90

Boil Gravity: 1.048

Efficiency: 75

Mash Thickness: 3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 18 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/25/2016 5:49 PM

Notes:

Author:

Boil Size: 7.5 Gallons

Boil Time: 60

Boil Gravity: 1.052

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 1.25

Primary Temp: 65 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/25/2016 2:10 PM

Notes:

Author:

jhanson1526

Boil Size: 14.5 Gallons

Boil Time: 90

Boil Gravity: 1.058

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 68 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 10/4/2015 5:48 PM

Notes:

Author:

Bakke Brygg

Boil Size: 55 Litres

Boil Time: 80

Boil Gravity: 1.05

Efficiency: 72

Mash Thickness: 3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.5

Primary Temp: 20 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 9/16/2015 9:48 AM

Notes: Krydder i humlepose, tas ut etter nedkjøling.
Kandissukkeret tilsettes 10 min før kokeslutt.
Unngå det hvite fra appelsinen.

Strike Water Temperature: 72° C
Sparge Water Temperature: 76.4° C

Gjæring/primærgjæring 7 dager ved 20 grader
Modning/sekundærgjæring 14 dager ved 15-20 grader
Lagring 27 dager ved 10 grader

Author:

Boil Size: 50 Litres

Boil Time: 60

Boil Gravity: 1.047

Efficiency: 75

Mash Thickness: 30

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 25 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 8/6/2015 8:27 PM

Notes:

Author:

DasBeef

Boil Size: 15 Litres

Boil Time: 60

Boil Gravity: 1.072

Efficiency: 67

Mash Thickness: 2.7

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 7/8/2015 1:34 PM

Notes: