Homebrew Beer Recipes | Page 466 | Browse 315,000+ at Brewer's Friend

Author:

cody6173

Boil Size: 3 Gallons

Boil Time: 60

Boil Gravity: N/A

Efficiency: 35

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: Extract

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/3/2013 1:14 AM

Notes:

Author:

Wolf Pack Brewing

Boil Size: 37.85 Litres

Boil Time: 90

Boil Gravity: 1.041

Efficiency: 75

Mash Thickness: 3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 16 ° C

Priming Method: co2

Priming Amount: 2.01 bar

Creation Date: 1/12/2021 10:15 PM

Notes: https://beerandbrewing.com/loving-summer-blonde-ale-recipe/
https://www.youtube.com/watch?v=TGmYdl-qBxs

Mill the grains and mix with 3 gallons (11.2 l) of 163°F (73°C) strike water to reach a mash temperature of 152°F (67°C). Hold this temperature for 60 minutes. Vorlauf until your runnings are clear, then run off into the kettle. Sparge the grains with 4.3 gallons (16.2 l) and top up as necessary to obtain 6 gallons (23 l) of wort. Boil for 60 minutes, following the hops schedule.

After the boil, chill the wort to slightly below fermentation temperature, about 60°F (16°C). Aerate the wort with pure oxygen or filtered air and pitch the yeast. Ferment at 60°F (16°C) for one week, then allow temperature to free rise to 70°F (21°C). Upon completion of fermentation, add dry hops and wait 2–3 days. Crash the beer to 35°F (2°C), then bottle or keg and carbonate to approximately 2.5 volumes of CO2.

Author:

Boil Size: 25 Litres

Boil Time: 60

Boil Gravity: 1.071

Efficiency: 75

Mash Thickness: 3.25

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/27/2015 2:52 PM

Notes:

Author:

chewyheel

Boil Size: 6.5 Gallons

Boil Time: 60

Boil Gravity: 1.041

Efficiency: 75

Mash Thickness: 3.15

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 66 ° F

Priming Method: co2

Priming Amount: N/A

Creation Date: 10/16/2020 9:57 PM

Notes: Hit all my numbers, good brew day.

Author:

Bray Brew

Boil Size: 7 Gallons

Boil Time: 60

Boil Gravity: 1.045

Efficiency: 65

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: BIAB

Pitch Rate: 0.35

Primary Temp: 66 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 11/7/2015 4:08 PM

Notes:

Author:

Pazete

Boil Size: 150 Litres

Boil Time: 60

Boil Gravity: 1.038

Efficiency: 65

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.75

Primary Temp: 17 ° C

Priming Method: co2

Priming Amount: N/A

Creation Date: 1/13/2016 11:19 PM

Notes:

Author:

IPAlligator

Boil Size: 365.9 Gallons

Boil Time: 60

Boil Gravity: 1.058

Efficiency: 75

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 66 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/10/2017 4:07 AM

Notes:

Author:

Belgian Samurai

Boil Size: 1.5 Gallons

Boil Time: 30

Boil Gravity: 1.152

Efficiency: 35

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: Extract

Pitch Rate: 1.0

Primary Temp: 69 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 12/15/2014 1:23 AM

Notes: I have the liquid extract can size set at 3.3lb's, because that's the only number I could find on the net. I guess it's correct.

This recipe does equal the actual abv according to the hydrometer reading.
OG: 1.154
(post wort [aka post yeast-pitch] day-#2 in carboy: 1.024)
FG: 1.014
Supposedly, that should equal 18.3% abv., but this recipe calculator suggests 3.9%. I'm not convinced it's 18%, but it's sure not 3.9% either! Perhaps it is stronger than I think, b/c I usually have a bit of a head-pounding afterward.

Is priming sugar not included in this form?

Author:

Tuomo

Boil Size: 25 Litres

Boil Time: 90

Boil Gravity: 1.066

Efficiency: 70

Mash Thickness: 3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/15/2016 9:59 AM

Notes:

Author:

Kaan

Boil Size: 20 Litres

Boil Time: 60

Boil Gravity: 1.055

Efficiency: 70

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: Partial Mash

Pitch Rate: N/A

Primary Temp: 21 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 4/24/2016 6:39 PM

Notes:

Author:

EvanAltman36

Boil Size: 5.5 Gallons

Boil Time: 70

Boil Gravity: 1.06

Efficiency: 45

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: Extract

Pitch Rate: 0.75

Primary Temp: 70 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 2/25/2013 12:22 AM

Notes: Pitch 2 packets Safbrew S-33

Author:

Camp Rock Grove Brewing

Boil Size: 3 Gallons

Boil Time: 90

Boil Gravity: 1.179

Efficiency: 51

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: Extract

Pitch Rate: 1.0

Primary Temp: 72 ° F

Priming Method: Forced CO2

Priming Amount: N/A

Creation Date: 1/16/2017 6:47 PM

Notes: BREWING NOTES:
-- A yeast starter and 2-stage fermentation is highly recommended
for this beer.
-- 6 gallon batch size - This recipe has been calculated to
produce 6 gallons to accommodate wort losses due to the
ridiculous amount of hops
-- 90 minute boil
O.G: 1.090 READY: 8 WEEKS
2 weeks primary, 2–4 weeks secondary,
2 weeks bottle conditioning

Author:

Mikulin Vasyl

Boil Size: 1150 Litres

Boil Time: 90

Boil Gravity: 17.5

Efficiency: 81

Mash Thickness: 3

Sugar Scale: Plato

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 20 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 6/21/2016 11:55 AM

Notes:

Author:

mboman

Boil Size: 7 Gallons

Boil Time: 60

Boil Gravity: 1.042

Efficiency: 35

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: Extract

Pitch Rate: 0.35

Primary Temp: 72 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/13/2015 1:40 AM

Notes: Step by Step

In this extract recipe, the oats are not going to provide any sugars for fermentation so the amount of malt extract is greater than the other recipes. Place the oats loosely in a grain bag. Since the oats will swell, avoid packing them too tightly in the bag. Use more bags if needed. Steep the bag in 2 gallons (~8 L) of 170 °F (77 °C) water for about 30 minutes. Lift the grain bag out of the steeping liquid and rinse with warm water. Allow the bags to drip into the kettle for a few minutes while you add the malt extract. Since this is only oats, squeeze the bags to extract the liquid. Add enough water to the steeping liquor and malt extract to make a pre-boil volume of 5.9 gallons (22 L) and a gravity of 1.043 (10.6 °P). Stir thoroughly to help dissolve the extract and bring to a boil.

Once the wort is boiling, add the bittering hops. The total wort boil time is one hour after adding the bittering hops. Chill the wort rapidly to 68 °F (20 °C), pitch the yeast and aerate thoroughly. Follow the fermentation and packaging instructions for the all-grain version.

Begin fermentation at 68 °F (20 °C) slowly raising temperature to 72 °F (22 °C) by the last one-third of fermentation.

Instructions provided from: https://byo.com/stories/item/1647-witbier-style-profile

Author:

514alastair

Boil Size: 8 Gallons

Boil Time: 60

Boil Gravity: 1.038

Efficiency: 72

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: BIAB

Pitch Rate: 0.35

Primary Temp: 60 ° F

Priming Method: N/A

Priming Amount: N/A

Creation Date: 10/8/2016 1:00 PM

Notes: v.2: addition of Carafe produces a great colour, and an almost nutty taste (good).
Poor head retention but happy otherwise! Will do this again.

v.1 the original recipe called for Crystal 120, but this was unavailable, so subbed this is Crystal 80. Colour obviously lighter than desired.

Should have added a fining agent - 3 weeks in the bottle and it's still cloudy, but first bottle was good. I anticipate this will need at least another month to age.

Author:

DewsBrews

Boil Size: 21 Gallons

Boil Time: 60

Boil Gravity: 1.062

Efficiency: 70

Mash Thickness: 1.3

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: 0.35

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 1/15/2020 1:44 AM

Notes:

Author:

metsis

Boil Size: 7 Litres

Boil Time: 90

Boil Gravity: 1.138

Efficiency: 35

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: Extract

Pitch Rate: 0.35

Primary Temp: 20 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 5/28/2015 3:37 PM

Notes:

Author:

Meddo

Boil Size: 31.3 Litres

Boil Time: 60

Boil Gravity: 1.032

Efficiency: 80

Mash Thickness: N/A

Sugar Scale: Specific Gravity

Brew Method: BIAB

Pitch Rate: 1.0

Primary Temp: 18 ° C

Priming Method: Force

Priming Amount: N/A

Creation Date: 11/28/2016 10:26 PM

Notes: * Hop stand at flameout for 10-15 minutes before rapid cooling to 18 deg.

* 50:50 mix of WLP001 / WLP017

Recipe asks for Simpsons Dark Crystal (80L), subbed with placeholder US Crystal 80L.

Assuming 4L lost in kettle, target FV volume 21L for 19L kegged.

Recipe in this thread (post #13):
http://aussiehomebrewer.com/topic/91049-young-henrys-real-ale-clone/

Author:

Boil Size: 30 Litres

Boil Time: 60

Boil Gravity: 1.044

Efficiency: 70

Mash Thickness: 3.1

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: 22 ° C

Priming Method: N/A

Priming Amount: N/A

Creation Date: 6/12/2016 4:39 PM

Notes:

Author:

Taquina

Boil Size: 8 Gallons

Boil Time: 60

Boil Gravity: 1.004

Efficiency: 70

Mash Thickness: 1.5

Sugar Scale: Specific Gravity

Brew Method: All Grain

Pitch Rate: N/A

Primary Temp: N/A

Priming Method: N/A

Priming Amount: N/A

Creation Date: 7/13/2017 3:49 PM

Notes: For those of you who don’t want to sit around for hours chewing up corn (we know who you are), use the following recipe. Crush the germinated corn coarsely and pour in the brewpot with 8 quarts of cold water. Sit and let sit one hour. Bring it to a boil, add the sugar, then lower the heat and simmer three hours (stirring regularly). Add whatever spices you desire at the end of the boil. In this recipe we use cloves but you can use anything from cinnamon to ginger. Remove and let it sit for one hour. Next, strain the liquid into a fermenter using a strainer, cheese cloth or any other method you prefer. Once it cools to 70° F (21° C), pitch the yeast and ferment at room temperature (between 60 and 75° F) for five days. Rack to secondary and ferment for one to two weeks until clarified. Bottle using 1 teaspoon corn sugar per bottle for priming. Finally, let it sit two more weeks after bottling before drinking.

Ingredients (1 gallon)

8 quarts water
1 pound germinated corn (jora)
2 cups brown sugar
8 whole allspice or cloves
ale yeast