What are you doing with homebrew today?

[Craigerrr]

Brewing a Julius while I have everything out. To hot outside to do anything

Julius I presume is a hazy/juicy brew?

 

[Brew Cat]

Julius I presume is a hazy/juicy brew?

You've never had? Where do you live
https://treehousebrew.com/julius-ipa

 

[Craigerrr]

You've never had? Where do you live
https://treehousebrew.com/julius-ipa

Southwestern Ontario, about an hour west of Toronto, 1.5 hours northeast of Buffalo NY. I have heard of Treehoise, but have never had the pleasure. This is right up my alley, could you share the recipe?

 

[Brew Cat]

Yes well they don't distribute but they can it. You have to go the the brewery.
https://www.brewersfriend.com/homebrew/recipe/view/1445265/julius

 

[Brew Cat]

Yes well they don't distribute but they can it. You have to go the the brewery.
https://www.brewersfriend.com/homebrew/recipe/view/1445265/julius

Your gonna like this one
It's the most expensive beer I make but worth it.

 

[Craigerrr]

Your gonna like this one
It's the most expensive beer I make but worth it.

Thanks, do you have a picture of yours?

 

[Donoroto]

I thought it would be fine...
Maybe I just go with my gut feeling

What’s the worst that could happen? Beer ruined? It’ll be fine.

 

[Dave Y]

I’m arguing with my tilt about when and where it should be providing readings. It seems to not like my insulated 14 gallon fermenter very much.

 

[Donoroto]

I’m arguing with my tilt about when and where it should be providing readings. It seems to not like my insulated 14 gallon fermenter very much.

Threaten it. It worked for me.

My stainless tank has a 4” TC at top, I made one from polycarbonate, it helped a bit. My ferm fridge is also stainless, I have my Pi Zero right next to the plastic doir seal so it picks up the tilt signal. We’re dealing with low power here, so distances need to be small. Even a sealed keg will leak RF a bit, if you’re close enough.

 

[Brew Cat]

Today brewed a third beer for the week, an ESB
Also mesured grains out for the next 3. Plan on dumping on the cakes as they come due. First another summer wheat on the Schneider Weiss cake then a Sip of Sunshine on the Julius cake. The ESB cake will be for an oyster stout which I need to get grain for. I also need a German ale yeast for an Altbier I've measured out

 

[Dave Y]

Threaten it. It worked for me.

My stainless tank has a 4” TC at top, I made one from polycarbonate, it helped a bit. My ferm fridge is also stainless, I have my Pi Zero right next to the plastic doir seal so it picks up the tilt signal. We’re dealing with low power here, so distances need to be small. Even a sealed keg will leak RF a bit, if you’re close enough.

Ok, I gave that tilt a choice; Straighten up, or I sell it to a brewer who does sour beer
so THERE.

Here is literally the ONLY place I get a reading on both my phone and this inexpensive tablet.
I think I may upgrade to a tilt mini pro to see if that helps. I’ve only seen the issue in my pressure capable fermenter, which is a bit more stout than my other fermenters.

 

[Zambi]

You'll all not be surprised I changed my mind again.
Next up will be a simple ginger concoction on old trub and probably some beer that stays behind (when the keg is full).
Just water, sugar and a little hop (maybe some lime juice or peel). Boiling only for the sugar to dissolve

 

[Craigerrr]

Threaten it. It worked for me.

My stainless tank has a 4” TC at top, I made one from polycarbonate, it helped a bit. My ferm fridge is also stainless, I have my Pi Zero right next to the plastic doir seal so it picks up the tilt signal. We’re dealing with low power here, so distances need to be small. Even a sealed keg will leak RF a bit, if you’re close enough.

What is this voodoo of which you speak