Mash Efficiency

[cowboy7307]

if i look at a recipe and its efficiency says 80%
and i am doing BIAB and i think my efficiency is say 65%
how do i adjust the recipe to suit BIAB

 

[Mont Y. Märzen]

Under Profile > Edit > General, set your preferred Method to BIAB.

For each Equipment Profile, you can set the Average Efficiency.

You can also change these in the recipe editor directly, but setting them in those places first will default a new recipe to use your own numbers and method.

65% is a bit low for that method though. Be sure to research the BF article on efficiency calculations, and be sure to meticulously measure all of your volumes and losses for several batches. (do not estimate - measure.) After about 5 or so batches, you should have a good running average for efficiency that will stabilize. Also, be certain you are mashing to complete 100% conversion, not just by time. (use an iodine test if you can) The efficiency article will show why that is important. If you are inconsistent with mashing to full conversion, your efficiency will be all over the map.

 

[Brew Cat]

Yeah
That's a problem with copying recipes
That don't give the efficiency
Put the recipe in the recipe builder and also their efficiency then in the tools section you can see scale by efficiency

 

[RyNo Brew]

That’s a solid way to use the BF Recipe Builder. Once you’ve set your brewing method (BIAB) plus brewhouse efficiency and switched the target mode to Goal: O.G., you can basically “reverse‑engineer” the recipe. Enter each fermentable with its exact weight, and the builder will immediately show how far above or below the target gravity you are. From there it’s just a matter of nudging the grain amounts until the projected O.G. lines up with the goal. It’s a nice, visual way to sanity‑check a recipe and make sure the numbers actually match the intended gravity. This works for hop additions and target IBU.

Cheers!

 

[Minbari]

That’s a solid way to use the BF Recipe Builder. Once you’ve set your brewing method (BIAB) plus brewhouse efficiency and switched the target mode to Goal: O.G., you can basically “reverse‑engineer” the recipe. Enter each fermentable with its exact weight, and the builder will immediately show how far above or below the target gravity you are. From there it’s just a matter of nudging the grain amounts until the projected O.G. lines up with the goal. It’s a nice, visual way to sanity‑check a recipe and make sure the numbers actually match the intended gravity. This works for hop additions and target IBU.

Cheers!

Never had allot of luck doing it that way. Too many variables that cause efficiency to change.

Easiest way i have found:

Mash
Boil
Take SG reading.
Add water to make SG what you wanted
Ferment

Your volume will vary, but the beer comes out right every time

 

[Ozarks Mountain Brewery]

I'll be honest, I dont take readings anymore or worry about gravity but I was obsessed years ago so go for it, my final word is it usually tasted good and that's all that matters

 

[Mike at Bay]

So today I brewed a pilsner (my first). Been brewing off and on, extract and all grain BIAB for years but had not really been overly concerned about the numbers. HOWEVER, now that I am retired I have been trying to add a bit more science to the brew. So again, today I brewed a pilsner....a relatively small grain bill given that I have been brewing porters, stouts and ales. I decided that today I would introduce the iodine test to my brewing as my efficiency had been in the up 60's low 70's. WELL, I mashed in the bag for 90 mins till the iodine said I was done.......and......way high on my numbers (1.040 vs expected 1.034). Volumes were fine....PH was fine.....but PB gravity was 6 points higher than expected. Using the dilute calculator I added a gal of distilled water (calc called for 1.30 gals but I had a gal on hand). My gravity numbers are now pretty close (not exact) to expected.

My question.....as has been mentioned above.....recipes online have no clue around efficiency (mine or their's). SO, If my efficiency it truly 83% as I achieved today pre boil after a 90 min mash, in the future should I curtail the grain volumes to achieve the style numbers. For example, today I could have probably used less grain/corn and achieved the proper gravities for the style.

I think this plays to the comment about copying recipes versus creating your own from scratch.

Hope all this makes sense.....been a long brew day.

 

[Brew Cat]

Well you could try just mashing for 60 minutes
I never needed to Go longer except maybe a high gravity beer