iSpindel calibration readings

Discussion in 'Feature Requests' started by Brewer #70824, Sep 8, 2020.

Tags:
  1. Brewer #70824

    Brewer #70824 New Member

    Joined:
    May 3, 2019
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    1
    Hi
    For helping in calibrating an iSpindel it would be really helpful if it was possible to see the angle readings from any (iSpindel) device under devices, updated everytime the iSpindel send an update. This way it is really easy to set the update interval in the iSpindel to 60s, and then get the angle readings during calibration in water with different sugar content. This feature is available in Brewfather, but I really miss it here in Brewersfriend, because it's what I normally use.
    BR
    Nicolaj
     

    Attached Files:

  2. Yooper

    Yooper Administrator
    Staff Member

    Joined:
    Nov 16, 2013
    Messages:
    2,494
    Likes Received:
    1,582
    Trophy Points:
    113
    Gender:
    Female
    Occupation:
    Happily retired
    Location:
    Upper Michigan/Florida
    I'll see what we can do! Thanks.
     
  3. Yooper

    Yooper Administrator
    Staff Member

    Joined:
    Nov 16, 2013
    Messages:
    2,494
    Likes Received:
    1,582
    Trophy Points:
    113
    Gender:
    Female
    Occupation:
    Happily retired
    Location:
    Upper Michigan/Florida
    Thanks for waiting! I don't have an iSpindel, so I had to check with the developer, but you can do that with Brewer's Friend.

    You can see the angle reading:
    [​IMG]

    You do have to link it to a brew session first, but otherwise it should be unremarkable.

    https://www.brewersfriend.com/homebrew/profile/device_settings
     
  4. Brewer #70824

    Brewer #70824 New Member

    Joined:
    May 3, 2019
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    1
    Thank you very much for answering.
    You are right. But the problem is, that even if I set the update interval on the iSpindel to 1 minute, there is still the 15 minutes limit on Brewersfriend for receiving data, and you need to refresh the page to see the new reading. This means that a calibration involving 6 sugar solutions would take 1,5 hours instead of 6 minutes. Plus it is a lot of extra annoying mouse clicks to link it to a brew session :)
     

    Attached Files:

  5. Brewer #70824

    Brewer #70824 New Member

    Joined:
    May 3, 2019
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    1
    Hi,
    Please react on my post from september 9th. Thanks
    Nicolaj
     
  6. Pricelessbrewing

    Pricelessbrewing QA Software Tester
    Staff Member

    Joined:
    Jun 8, 2016
    Messages:
    766
    Likes Received:
    503
    Trophy Points:
    93
    Gender:
    Male
    I'm only casually familiar with iSpindel, but I've sent a message to @Yooper and the developers to followup on calibrating multiple devices.

    Thank you for your patience.
     
  7. mtrepanier

    mtrepanier New Member

    Joined:
    Nov 22, 2020
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Occupation:
    Software Engineer
    The easiest way I found to calibrate the iSpindel was with ubidots as it support 15 seconds data. So I set my iSpindel to connect to ubidots. I can do more then 1 iSpindel in the same time while calibrating
     

Share This Page

arrow_white